Linda February 01, 2021 for Model Number Whirlpool Stackable We have a stackable Whirlpool W/D set. When filling.... the water coming from the inlet valve to the Syphon break spills out through the holes at the top of the inlet valve. It looks like the part W10919200 is not currently available immediately. Can we do anything to bypass the Syphon break until the inlet valve for this machine comes back in stock?
1 Answer Hello Lisa, we cannot advise on bypassing a safety feature on an appliance. The siphon break prevents cross-contamination of potable water in your home. Read More...
K.C.6969 April 11, 2016 for Model Number LA412 replaced moter after 35 yrs it was smoking and heat safety shut down. thought it was fixed ,new belts, tried it out in spin cycle ok. ashed a load and it made some squeels an d didn't pump water out. pump?
1 Answer K.C.6969, You will want to check the drain pump to make sure that it is not siezed up, which would be the most likely issue. The pump part number is WP6-2022030. Read More...
John M. October 25, 2015 for Model Number maytag model LAT9200AAL What type of clamp do you use to clamp a siphon break hose from pump to siphon break?
Jeff December 12, 2014 for Model Number LAT9800AAW I need to order the siphon break and drain hose. Do I need any additional gaskets or clamps than what comes with the siphon break?
Mario M. September 29, 2014 for Model Number LA882 I recently ordered part #208847. I broke off the drain elbow coming out of the back of the washer (small part of it is still sticking out). It seems that this part that I ordered goes on with a twist lock motion, as it has tabs! But the remaining part on the washer has (4) screws holding it in place, and the only way to connect the new, with the old is to remove the screws, and disconnect the broken part that is still connected to the part inside the machine. How do I open the back of the machine to get at the parts? Is there a video showing the repair process?
1 Answer Hello Mario, Unplug the unit before beginning to prevent injury or death from electrical shock. To open the unit you need to remove the two large Phillips head screw at the bottom of the front panel and remove the front panel. Now you will need to remove the two 3/8 inch head screws, one on each side. This will allow you to raise the main top and access the part. Read More...
1 Answer Chet, Water will shoot out of the top of the siphon break because of the plunger at the top being bad in which the siphon break would need to be replaced. Read More...
Frank January 18, 2014 for Model Number A209 When washer is spinning in fast mode it shakes too much. I've taken front cover off. I don't see anything obvious. Does anyone have any idea?
Ed October 28, 2013 for Model Number 70s series washer I have a 70s series kenmore that doesnt pump all the water out after wash cycle. When it spins it throws water out top of tub 3quarter in exhust drain. Is it that the drain is not big enough or timer worn out? There seams to be good pump pressure.
1 Answer Hello Ed. It sounds like the clutch is bad and will need to be replaced, if the drain pipe in the house in not clogged and backing up. I would check that first. Read More...
Connie December 06, 2012 for Model Number kitchenaid front-loading automatic washer To whom it may concern, My washer will got thru the wash cylce then when it come time for it to go to the rinse cycle i get the code F02 it will agitate but it doesnt seem to want to spin at a high speed i was just wondering if its the pump or something a little more easier we have checked the hoses for drain problems, we even took a shop vac and attached it to the drain hose and when we do that everything works good and it seems to go thru cycle and spins like normal iI have been workin on this for 2 days and i am puzzled any help or info would be greatly appreciated thank you for taking the time Connie T
1 Answer Hello Connie. Check the pump and see if it is clogged. If not, and it does not drain, replace the pump on the unit. Read More...
Jimbeau November 23, 2011 for Model Number lat9605aae--part number 206638 Can I just bypass the syphon break by clamping a connector between the two hoses?
1 Answer Hi Jimbeau. You can try as long as the drain water does not back up on you. There has to be a air "break opening" in order to let air in when the drain is in progress. The Siphon break is part # 206638. The gasket is a separate part # WP214765. Thank You. Read More...