Trina December 31, 2014 for Model Number MAV8000AWW From what I see the snubber ring is needing replaced on my washer. Question is, if replacing that what all else should be replaced, or is it too costly to repair?
1 Answer Hello Trina. If just the snubber is bad and the unit is unbalanced, you will only need to replace the snubber. Read More...
Stevens September 08, 2014 for Model Number Maytag atlantis top load (10 years old My top load maytag began shaking badly on spin cycle I replaced the snubber ring and belt and it was o.k. for about 2 weeks then all of the sudden again on spin its now making a banging noise (moe like a belt slapping) on spin from the transmission area. Checked thrust pulley for travelk o.k. checked belt and motor all appear o.k. Its just this noise (load) when at full spin empty or full. Any idea's?
1 Answer Stevens, The model number of the unit will help when posting a question but for your issue the first thing to check would be the drain pump. If this checks ok then having the model will help for further assistance. Read More...
Jeysen April 24, 2014 for Model Number Maytag PAVT144AWW Rev.23 My washer doesn't spin correcly. My clthes are soaking wet even after an other spin cycle. during the agitating cycle there is a clanking noise. Also, when I open the lid or the spinning cycle is finished, The tub stop really brutal with a screaching noise. There is a lot of white dust Under the washer that seems comming from the snubber. I checked the thrust bearing and it doesn't seems to be worned. The cam is moving freeely against the pulley. When turning the pulley CW, the agitator moving correctly. In CCW, the agitator moves as if I'm turning it CW. The cam barely reach the first marker, I don't feel any resistance and the brakes are not released. I'm able to release them if I push the cam completly to the end with a screw driver. Am I facing a thrust bearing or brake issue ??? or both ?? Thank you
1 Answer Hello Jeysen. It sounds like a thrust bearing issue. However, if you replace the thrust bearing and the issue continues, then the transmission is the problem with the unit. I would also replace the snubber if there is a lot of white shavings under the unit. Read More...
Tom December 12, 2013 for Model Number Crosley CW6000 Hi, My 8 year old washing machine crewed up the snubber ring. I replaced it and again see white shavings. I'm going to change out all 6 springs and install a new snubber this weekend. What could be the cause of snubber ring failure? Thanks
1 Answer Hello Tom. It could be the spring. But be aware, when you install a new ring, you will get a few of those shavings from a new ring. That is common. Read More...
1 Answer Hello Chas. Check the thrust bearing kit 12002213 and see if it is bad and will need to be replaced on the unit. You can test the thrust bearing manually, by turning the pulley clockwise it should agitate, and by turning it counterclockwise it should release the brake and spin the tub. You can also remove the thrust bearing and inspect it for wore or broke brearings. Read More...
Mike June 28, 2013 for Model Number mav5758eww maytag Hi there, what special tools do i need to change out the tub bearing and seal kit,and also best way to remove the outer tub springs. while its out should i change the snubber ring it does shake alot
1 Answer Mike, There is a spring removal tool for the springs which is part number TJ22002922. There is a seal nut tool TJ22002898 and spanner wrench TJSHSW-1 for the hub and seal nut. The spanner wrench is not available any longer and there is a brake tool that is no longer available. Read More...
1 Answer Ana, The friction ring/snubber 36108 could create a vibration issue if it is badly worn or "sticking" to the base or isolator. You will also need to check the centerring springs 35948 and ensure they're not stretched out or have loss their tension, and the base to make sure it is not cracked or flexxing when the tub moves. Read More...
Lucuas March 27, 2013 for Model Number MAV6300AWW The washer has a lot of vibration and moves all over during the spin cycle. The floor and machine are all level, could this be a bad snubber? The current one has a lot of shavings, but appears intact.
1 Answer Hello Lucuas. Yes, if the snubber is bad, it will cause the issues you are having with the unit. Read More...
Richard January 31, 2013 for Model Number Mav3855aww The washer squeaks when in agitator cycle. What is the like cure? Thank you.
1 Answer Hello Richard. Based on the information you provided, you will need to replace the brake WP35-6714, stator WP35-6918, and the snubber WP21002026 on the unit. Read More...
Rockinrobin January 22, 2013 for Model Number AAV7000AWW Rev. 23 I need to replace the Snubber Ring but according to the Diagrams, this Washer has 2 of them (1 on the Base Diagram & 1 on the Transmission Diagram under the Brake). Therefore, do I need to order 1 or 2 Snubber Ring(s)?
1 Answer Hello Rockinrobin, There is only 1 snubber ring on the unit and it is located under the brake. Read More...