Tracy July 27, 2011 for Model Number mavt634aww When my maytag atlantis goes to spin cycle, it starts making a popping noise, and you can see the center pulley on the bottom falling down about a half an inch. When it pops, tub slows every time it pops and doesn't spin water out good. Please help. Thank you.
1 Answer Hello Tracy. Based on the information you provided, it sounds like the thrust bearing 12002213 is bad and will need to be replaced. Hope this helps. Read More...
Wayne July 26, 2011 for Model Number PAV2360AWW After removing inner tub, outer tub and agitator, cleaning removed items, replacing the snubber seal, belt and tension springs and put all back together, in the wash cycle only the transmission is very noisy. What did I do wrong
1 Answer Wayne, You probably didn't do anything wrong. You most likely forgot to properly readjust the thrust bearing cam assembly and the gearcase gears arent meshing properly. Thanks and Good Luck. Read More...
Scott May 18, 2011 for Model Number PAV2200AWW Ok, so I know that I need to replace the snubber since my washer shakes so bad that it literally has shaken the screws/nails out of the sheet rock in my hallway, but I also feel like that I need to replace the brakes since is squeals when it stops a cycle. Here is the thing, I cannot seem to find the part #'s for the brakes from you.
1 Answer Hello Scott. Here is the brake WP35-6714, snubber WP21002026, and the stator WP35-6918 for the model number you provided. Hope this helps. Read More...
Jason J. May 05, 2011 for Model Number mav9600eww When the washer stops the brake makes a loud screech. Also, the water pump is making a whining sound and the pully turns rough.
1 Answer Hello Jason! You will need to change out the pump, brake stator and snubber. We will need your appliance serial number to verify the correct part numbers you will need as there is a series change within this unit. Thanks. Read More...
Lou April 22, 2011 for Model Number MAV9600EWQ Machine periodically goes off balance and heads across the room. I have checked level several times. I note that agitator / tub appears to be "stuck" after machine sits unused for a while. If I free up agitator / drum prior to spin cycle then things seem to be okay. Question: What's causing this "sticking"? I do not see anything that appears to contribute.
1 Answer Hello Lou. It sounds like the snubber ring is bad. You will need to look for plastic shavings in the bottom of the machine. If there are some, the snubber ring WP21002026 will need to be replaced to balance the machine. Also, check the thrust bearing 12002213 and make sure it is releasing the brake properly. You can turn the pulley by hand and see if it is releasing the brake assembly. Hope this helps. Read More...
1 Answer Hello Barbara. You can turn the thrust bearing several times to rotate the inner tub assembly. You should hear a roaring sound or feel dragging if the tub bearing is bad. Hope this helps. Read More...
Barbara T. April 06, 2011 for Model Number MAVT446AWW I removed belt and hand turned thrust bearing by hand. It turns freely, but you have to turn it about 1/2 turn before it grabs. Is there a problem?
1 Answer Hello Barbara. No, that is working properly. Did the pump seem to be ok as well? If so, make sure the tub bearing is not bad. Hope this helps. Read More...
1 Answer Hello Barbara. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/general-talk/4120-maytag-performa-washer-snubber-replacement.html Read More...
Barbara T. April 06, 2011 for Model Number MAVT446AWW While washer is spinning it makes a loud whirring noise.I moved washer out from wall and see a (what seems like) white tiny plastic shavings. What is wrong?
1 Answer Hello Barbara. The plastic shavings are from the snubber. If it is making a noise, you will need to check the pump WP35-6780 and the thrust bearing 12002213. You will need to lean the washer back and turn the pulleys by hand, with the belt removed. Hope this helps. Read More...