Linda March 09, 2012 for Model Number MAV208DAWW OK Still trying to troubleshoot so I get the correct part/parts. Now the washer agitates a few seconds then stops then just hums like during wash cycle, during those few seconds of agitation it makes aloud clanking/knocking sound but stops once agitation stops. It seems to empty out/drain ok. Does this help to better identify the part I need to replace?
1 Answer Hi Linda. Lift and support the unit. If you see the plastic shavings from the snubber ring part # WP21002026 it is normal. Remove the front panel and see if there are wear marks where the lower tub support(with the lower spin bearing) has a plastic snubber ring. If the unit has worn past the snubber ring and into the base it will wear out the base color and into bare metal. If this is the issue, it will make noise. You will need a new snubber ring. Make sure all spring hooks at each end w/grease in between metal areas are fully set in place. Rotate the lower pulley both ways. It sounds like you have a sticky brake rotor part # WP35-6714. It will loosen from the rotor and jam in between the brake stator part # WP35-6918 and make noise during agitation. Check these parts. Thank You. Read More...
Linda March 09, 2012 for Model Number MAV208DAWW I checked the previous suggestions and none of them appeared to be the problem with visual inspection. Since then the washer has started making a LOUD knocking/ grinding sound and after reading a few posts I wonder if it is the transmission or what?
1 Answer Hello Linda. If the thrust bearing 12002213, brake WP35-6714, and pump WP35-6780 are good, and the unit is grinding loud, it sounds like the transmission 35-6615 is bad and needs to be replaced. Hope this helps. Read More...
Linda February 23, 2012 for Model Number MAV208DAWW My washer works but makes a noise while agitating and spinning especially with heavier loads? Thinking snubber or springs but not sure any ideas?
1 Answer Hi Linda. Your washer will make a squeaking noise if the springs are not ok. Remove the front panel. gently push the tub towards the back. Use a flashlight to look at the snubber / base area. If you see fresh base metal worn through the base coating, then you need to change the snubber ring part # WP21002026. All springs need to use a dab of grease where they contact the tub hangers and at the lower bottom of the tub. Make sure they are connected all the way back up through the tub w/ grease underside the base. The spring hook tip may not be back pointed up and inserted back through the hole on the tub. This will allow the tip to remain down under the tub and pull the spring tighter on that one side. Mis aligning the tub and then allowing balance issues. Make sure all of the tub support brackets upper and lower bolts are snug. Is there any dirty water leaking from the underside of the tub where the transmission shaft enters it ? If so then it will be a upper spin bearing (and/or lower) tub seal assy. gone bad. part # W10219156. Thank You. Read More...
Al January 13, 2012 for Model Number RTW4340SQ0- Roper Washer I was informed that my problem was not in the balance ring around the top of the tub and that it might be the suspension springs in the bottom. However whenever I take the top ring (it does have some visible damage in one side)off and spin the tub it seems perfectly balanced, then when I place it back on it goes crazy. the washer is only a couple years old and the springs on the bottom look great. Do you still think I the problem is in the springs?
1 Answer Hello Al. There should only be one spring 285901 under the bottom, and it goes from the back bottom of the frame to the bottom of the tub assembly. If the balance ring WP387240 is damaged, then you will need to replace the balance ring. Usually on these models, that back spring either breaks or comes off, and it causes the unit to be off balance. Hope this helps. Read More...
Al January 12, 2012 for Model Number Roper Washer RTW4340SQ0 I think that I have correctly found the unbalance problem in my Roper washer. I am pretty sure that it is the Balance ring at the top of the inner tub. But just to be sure, please tell me if this ring should be filled up completely with water or only half way as min is. Also if it is suppose to be completely filled, then can I recharge it somehow?
1 Answer Hello Al. The balance ring on the unit should only be half filled. It sounds like the suspension spring 285901 may be bad on the unit and will need to be replaced. Hope this helps. Read More...
Dave January 05, 2012 for Model Number PAVT234AWW No plastic shavings at the bottom. Springs are all intacked. The unit goes off balance fequently. Can the springs just be weak?
1 Answer Hello Dave. Look for a crack in the base of the washer. If the base is not cracked, the snubber WP21002026 is bad and will need to be replaced. The springs should be fine on the unit. Hope this helps. Read More...
Bill S. December 12, 2011 for Model Number MAV6057AWW Recently my Atlantis washer began making a metalic clunking noise during the SPIN cycle, along with a slight vibration of the tub, but it appears to spin at the normal speed and properly removes water from the clothes. After some research on your site, I replaced the tension springs and snubber, but that didn't solve the problem. I have installed a new belt and thrust bearing kit about a year ago, and a new brake and stator about 2 years ago, all of which appear to be working ok. I am now considering replacing the transmission (AP4373431) which includes the tub seal assembly kit (AP4009404 - tub seals, spin bearing, gaskets). But before I do, I was wondering if these symptoms might indicate something else like a weak motor tensioner pully, or brake spring/retainer functionality. Any thoughts on my prediciment?
1 Answer Hello Bill. Based on the information you provided, it sounds like the transmission kit 35-6615 is what you will need for the unit. Check and make sure the pump assembly is turning freely on the unit. If so, replace the transmission and the bearings. Hope this helps. Read More...
Mark November 18, 2011 for Model Number Roper washer I submitted a question regarding my roper washing machine spin cycle being violent, yesterday, about the snubber, and the response was that this make doesn't have one, instead, it was the balance spring at fault. I checked the balance spring, it's a little rusty, but still intact. Could this still be the problem? Thanks, Mark
1 Answer Hello Mark. No, if the spring is hooked up, then check and make sure it is supporting the tub. Also, check the balance ring on the inner basket and make sure it is still filled with fluid. If not, replace the balance ring. Hope this helps. Read More...
Mark November 18, 2011 for Model Number Roper washer My Roper washing machine has recently been getting violent on the spin cycle, with the drum having a lot more motion than before. I read up a little online, and the snubber appears to be the common problem, would you agree this is probably the case, or is there some way I can check? Many thanks, Mark
1 Answer Hello Mark. No, the roper machine does not use a snubber. You will need to check and see if the suspension spring WPW10250667 is broke of off at the back of the unit. There is a great video on the parts page to help you with this. Hope this helps. Read More...
Michael August 09, 2011 for Model Number mav7450aww How do you change a snubber ring on a Maytag Atlantis? Also suspension springs? Thanks
1 Answer Hell Michael. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/general-talk/4120-maytag-performa-washer-snubber-replacement.html Read More...