Jim C. May 10, 2013 for Model Number 34JA-3TKXW On my model 34JA-3TKXW Magic Chef gas range, where exactly is the spark module located? And , if its bad, what part number do I order? Thank you.
1 Answer Hello Jim. The spark module is behind the back panel of the range on the bottom corner. You should see all the wires going to the module 12001596. Read More...
Linda J. May 08, 2013 for Model Number Amana ARG7300W I have a spark module on order with you and can't find a schematic to see where the existing module is .. is it under the cooktop or in the back?
Keith May 05, 2013 for Model Number sc8830ebb1 Were is the spark module located on a drop in 4 burner gas whirlpool?
1 Answer Keith, the spark module is located under the glass cook top and burners and mounted to the bottom of the burner box. You will need to remove power to the cooktop, turn off the gas supply and lift the cook top out of the counter top opening. Label and remove the grates, burner caps, burner mounting screws and drip pans, and burner knobs, then lift the top off the burner box. You may also want to order new burner mounting screws 7101P286-60 3 for each burner, as they have a tendency to be rusty or seized to the burner and either strip or break in the removal procedure. Read More...
Curt April 20, 2013 for Model Number Maytag model CRG7500AAW Two of the four top burners do not light. All four burners have gas flowing and can be lit with a match. Two burners show sparks; two other burners show no sparks. Clicking is audible when any of the four buner knobs are rotated to the "light" position. What part do I need to purchase and replace? Thank you !
1 Answer Curt, The spark module 12001596 is the most likely issue. But check the igniter on each burner to make sure they are not damaged or broken. Read More...
Bob March 18, 2013 for Model Number Crosley. CG3177XUA What is the easiest way to access range burner spark ignitor for replacement? Thanks
1 Answer Bob, Here's what we have " Spark Module NOTE: Requires removal of range from installation position. 1. Remove screws securing lower rear access panel. 2. Disconnect and label wire connections from the spark module. 3. Remove screws securing spark module to unit chassis. 4. Replace and reverse procedure to reassemble." Read More...
Mark March 17, 2013 Model # MGR4452BDO rear stove top igniters are inop. No spark. fronts are sparking in unison and working fine. any suggestions. is it just igniters or half the module is bad?
1 Answer Mark, You will want to pull the burner heads off and check the ignitors for cracks. It is possible that the ignitors are bad. The spark module would be less likely but still a possibility. To check the ignitor you will look for cracks and check continuity. If there is continuity then the ignitor is good. Read More...
Pete March 15, 2013 for Model Number CSG7000CAB I am concerned about the answer to my last question. You used the word ignitor and how dangerous it is to cross-wire on a gas stove. I replaced the spark module and the instructions say "input" either terminal can be used for line or neutral and the "output" terminals can be wired in any order . I also replaced one switch burner, the last in line with only two wires. So what cross-wire problem are you referring to.
1 Answer Hello Pete, I looked up the wiring configuration for your unit and this is not a consideration on this model. There have been models produced with what they referred to as a re-ignition module. These units would spark the burner that the flame had gone out on, so they are the ones that must be wired specifically to the burner ignitor in question. That is why some older models had different color wires for each surface burner. I apologize for any inconvenience and concern this may have caused you. The model you have can be wired in any configuration so you have nothing to worry about. Read More...
Pete March 13, 2013 for Model Number Maytag gas stove top CSG7000CAB I am replacing my spark module. I saw your reply to another person stating the stove has to be removed and the glass removed to replace the module. After I replace the module can I plug it in to test the spark, without a gas connection, while the unit is sitting on my work bench. If I can do that I would be able to test the switch burners at the same time.
1 Answer Hello Pete, You are correct that the unit has to be pulled to remove the main top and access the spark module. You can test these with no gas to the unit. Also, you should label the ignitor wires to prevent cross-wiring. Cross-wiring a gas cooktop can be extremely dangerous. Read More...
Brad March 13, 2013 for Model Number WG399LXUS04 I was hoping you could tell me where the spark module for my Whirlpool range is located. Thanks
1 Answer Hello Brad. The model number you provided is not working. This should be located in the bottom back side of the unit. Yoou may have to remove the back panel to access the part. Read More...
Fred February 28, 2013 for Model Number Jenn Air JGC1536ADS I have an exisitng spark module in my gas top stove in which a couple of the outputs have went bad. The existing item is labeled: Model: 07740-035 Customer P/N 7431P051-60 4+0 outputs 120vAC 50/60 Hz Lot 0731-4 Made in Brazil Can you recommend the appropriate replacement part? I do need the four outputs.
1 Answer Fred, The part number for the spark module for the cooktop is part number WP7431P066-60. Read More...