Walter December 04, 2021 for Model Number MAH5500BWW Should the plastic edge ring on the inner tub have water in it?
1 Answer Walter, Thanks for the question!!! Yes, the water helps with the balancing during spin. Read More...
Suzie Steres February 07, 2019 for Model Number 1999 Maytag Neptune 4000 front load washer (MAH4000AWW) Our old machine has over the last 6 months been making a loud airplane motor sound and vibrating when spinning, and just recently started leaking from the bottom. My home warranty repairman came, put his hand and fingers on the inner drum, moved it front to back, and said the drum supports were "bent", a condition only caused by overloading (mis-using my machine. ) He did not open up the back or top of the machine to check the inside drums, bearings, seals, supports, etc. Is his statement of cause correct? Can the spider supports be bent? I've heard they can be broken, but not bent. Are their other factors that would cause an almost 20 year machine to have bent supports?... like parts life expectancy, galvanic corrosion to the drum spiders, worn out seals and ball bearings? The home warranty doesn't cover "Mis-use". Even if I did want to repair this machine on my own, would it make economic sense?
1 Answer Suzie, We haven't seen "bent" arms either, we have seen them break or corrode to the point they no longer hold the spin basket in position. The information supplied would indicate a worn out set of tub bearings, for sure, this would allow the tub to vibrate and make the noise you described. If the spider assembly were cracked or broken, we'd also expect a Thumping or banging noise in the spin cycle especially in the high spin speed. The replacement parts are relatively inexpensive, but it is a time consuming and awkward repair. so the " would it make economic sense? " would have to be your choice. Thanks, Read More...
Dan S November 17, 2018 for Model Number MAH5500BWW Recently I have noticed bits of gray plastic in my clothes when i take them out. I started looking and the tube assembly has shredded leaving plastic in my clothes. I also seems that the balance has gotten bad as in bangs every time through spin cycle. From what i can see is there is an inner tub that has a heavy plastic ring that has failed. Unit is a little over 12 years old. Can it be fixed?
1 Answer Dan, This issue would most likely be caused by a faulty bolt that holds the spinner support to the spin basket that may have broken. This would be the most likely cause for this issue. Read More...
Roberta February 11, 2018 for Model Number MAH5500BWW May washer is front load. it doesn't spin out. when buzzer goes off, I need to open door, close the push spin then it sounds like it going to spin out of machine.
1 Answer Roberta, If the unit will not spin during the wash but will spin if you hit spin only then this issue will most likely be in the main control board. If the unit is making a loud jet engine grinding noise then this would be a bad bearing. Read More...
Bonnie August 11, 2016 for Model Number MAH300AWW Hello! I have an 18-year-old Maytag Neptune. It stopped spinning and makes a louder than normal noise. I had a repairman come and he told me (just by listening) that the bearings were out in the cylinder at the rear of the basket, and to get a new machine. I love this machine and would rather try to fix it if at all practical. Is/are the part(s) needed available? Do you agree with his advice?Thank you for any information! Bonnie
1 Answer Hello Bonnie. Yes, you will need to order 22004465 and W10181639 to repair the unit. It does sound like the bearings are bad. Read More...
Wayne December 13, 2014 for Model Number MAH5500BWW After replacing the front and rear seals along with the inner seal, the shaft on the drum does not appear to extend far enough(approximately 1") in the back. How can the drum be pulled further through.
1 Answer Wayne, If you have the outer tub separated then you will want to turn the inner tub opening down and then slide the outer tub over the shaft of the inner wash basket. You may need to push down slightly to get the outer tub to slide all the way down the shaft. Make sure that you removed the old seal ring off the spinner support. This would be a metal piece that would be located at the base of the spinner. Read More...
Ed August 20, 2014 for Model Number MAH5500BWW I took the washer completely apart, except for the drums, because my wife said it was leaking and we heard sloshing sounds. Turns out the sloshing is normal and it was leaking from a small tear in boot! Anyway, after I put it back together and slipped the belt back on the drive, it now makes a loud sound like it isn't balanced when spinning. Any ideas? Thanks!
1 Answer Ed, Remove the three rear baffles(paddles) and make sure the tub mounting bolts are tight. Also check the concrete counter balances are secured tightly to the outer tub assembly. Recheck and make sure the "boot" is properly installed and secured to the tub assembly and shroud. Read More...
Ed August 15, 2014 for Model Number MAH5500BWW There is water somewhere between the inner tub and the outer tub. When you turn the inner tub there is a sloshing noise. The entire machine is disassembled and I cannot find the water. Can only hear it. Doesn't seem normal. ?
1 Answer Hello Ed. Yes, that is the liquid in the balance ring in the unit. It is normal. Read More...
Pat June 29, 2013 for Model Number MAYTAG NEPTUNE MODEL MAH5500BWW Makes louder than normal noise when in the spin cycle on max extract loud howling noise not a metallic noise.
1 Answer Pat, The loud noise during spin would be caused by a bad bearing. You would need to have the rear outer drum of the unit. Read More...
Lee T. April 15, 2013 for Model Number MAH4000AWW My machine made a buzzing/sizzling sound for about 5 seconds about 2 minutes into the wash cycle, then the main motor quit. So far I have taken the motor out to inspect and it it looks and smells fine. I did notice that the vent hole on the rear of the outer tub had some metal filings present and the belt was running off center of the "spinner pulley" I would note, though I have heard no growling, and the the tubs spins by hand as free as always, I feel the spinner does not spin up as fast as it used to. Also, since I have the motor out would like to replace the motor isolators and the belt. What parts do you recommend to get me going again?
1 Answer Hello Lee. Based on the information you provided, it sounds like the motor and board kit 12002039 will need to be ordered and replaced on the unit. Also, the metal shavings will lead to the outer tub needing replaced due to a bad bearing. Read More...