Jonstaff February 26, 2014 for Model Number Jenn-air Glass Cooktop CCE3531B On two burners, rotary switch operates correctly but the light which shows the heat setting is burned out. What is the correct part number for replacing the light? Do I need to replace the switch itself or is light separate? NOT talking about the indicators that show burner has been used and is still hot. Just the lights under the control knobs. Thx--
John February 21, 2014 for Model Number 3531B On my Jennair cooktop the halogen burner comes on initially then turns off. Would this be the limiter switch?
1 Answer Hello John. Test the switch and see if your losing power from the switch. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Rajs January 06, 2014 for Model Number Jenn Air CCE3401 cooktop Hello, I am in need of two (2) INFINITE SWITCH for my Jenn Air CCE3401 cooktop. I need it for the following: 1) Left front 6" burner 2) Right front 9" burner My questions are: Will the Part Number AP4088404 (MFG Number 71001166 ) work for both positions? Do I need two different kinds of switches such that the knobs turn properly consistent with the heat level markings since one burner is on left and the other on the right? Thanks, RAJS
1 Answer Hello RAJS! Yes, you will use part number W11088181 for both the left front and left front burners. Thanks! Read More...
Dan December 05, 2013 for Model Number JENN-AIR Model CVE3401 I am in need of an INFINITE SWITCH (SINGLE) and I see it listed as MFG PN 71001166. I had purchased a switch (not from you) which has on it: INF-240TP-1177 240 VAC, 7403P405-60. I was assurred that it was the correct switch and it looks like it from an electrical stand point. The problem is that it only has 2 threaded mounting holes (where the one I am taking out has 4 holes even though only 2 are used) and the holes are 90 degrees off which would make the knob index completely wrong. The question is, does this switch have 4 mounting holes so I can rotate it 90 degrees in any direction so as to get the proper knob index? Regards, Dan
1 Answer Hello Dan. We need to know which element it is for so we can get you the correct switch. There is 3 listed for your model. Read More...
Henry November 13, 2013 for Model Number MAYTAG CSE9600ACB Hi: I have a 5 burner Glass Island Stove Top with the center rear (6") unit not working. The Infinite Switch does NOT feel like the other four and seems to be the problem. I have not taken it apart as yet but have looked at the unit carefully. I believe that I can take the side sheet metal screws off (8 of them ?) and lift the Glass Top off, putting it carefully to the side. Once I do that, are all the five switches mounted in the metal box? Do I simply remove and replace the switch, matching the wiring pattern of the new switch to that of the old one? Thanks. Henry
1 Answer Hello Henry. On the back of the switch the spades will be marked. Match the old markings to the new switch markings. Read More...
James September 29, 2013 for Model Number CCE3401B Jenn-air Cooktop The infinite switches connected to the knobs turn the elements on but don't seem to give me graduated heat as the knob is turned higher. A couple of the knobs will really only give a very high heat but no simmer or anything in between. Would replacing the switches cure that problem? The elements themselves all work
1 Answer James, Yes the infinite switches would be the cause of the unit only giving high heat and no simmer. Read More...
Rich July 10, 2013 for Model Number JED823OADB I have a Jennnaire range top. I believe an infinite switch has shorted out. I'm not sure which one. One of the four looks newer. Is it possible to test the switches? Or do these tend to die at a certain frequency of use. The range was made in 2001. Some water was spilled on the range, but the short wasn't immediate. about 2 min. later. Could this have weakened an already ill switch or have done it all on its own.
1 Answer Hello Rich. Test for power to the switch and then coming out of the switch. If there is power there, but no power out, then the switch is bad and will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jeff W June 12, 2013 for Model Number Cve3400b Does the switch include the light next to the control knob that indicates that the burner is on? My switch works, but the indicator light is always on. (Note: I am not talking about the light group that tells that a burner is hot).
Lois W. April 25, 2011 for Model Number CCE3531B I need to replace the infinite switch on my Jenn-Air cooktop. Would you be able to tell me how to remove the glass top so that I can access the switches. The stove is just a cooktop that is located in a center island. There is no oven attached just flush mounted in countertop. Help!
1 Answer Hello Lois. You will need to disconnect the power going to the unit. Then uninstall the unit where you can access the screws on the side of the burner box. Remove the knobs and the screws holding the cooktop in place. Lift the cooktop off the burner box and place it on a soft surface. Now you should be able to access the infinite switches. Reinstall in reverse order. Hope this helps. Read More...