Gordon July 04, 2016 for Model Number C221 Replacing jenn air burner control switch part #203147 with replacement 703147. the 203147 has 6 connections, the 703147 has only 5?
1 Answer Hello Gordon. Look and see if one of the wires on the old switch has a double spade on it. If so, you will wire it just as the old switch was wired on the unit. Read More...
Tamra September 17, 2015 for Model Number G102 No matter what heat setting I try to use, it is always heating to high degree. What part do I need to replace?
1 Answer Hello Tamra. You will need to order and replace the infinite switch on the unit. Read More...
Michael W June 11, 2015 for Model Number Jenn Air C301 I need to replace a surface element switch AP4291911 (Y703147), but first I need to know how to get to the old switch. It looks like the switch box comes out but I must not be finding all the screws.
1 Answer Michael, You will need to remove the exhaust grill on the downdraft and remove the 2 screws that are at the back of the escutcheon then push forward and up to release and remove the escutcheon. This will give access to the switch. Make sure that the power is off when doing this. Read More...
Jeff January 02, 2013 for Model Number Jenn Air C202 Following from an already posted question on your site, "the part number you supplied Y703147 is referred to as the figure 8 or double flat shaft, and the 700855K is referred to as the "d" shaped shaft. You stated your switch is not the "D" shaped... more shaft so you need to order Y703147. Read more: http://www.appliancepartspros.com/whirlpool-surface-unit-switch-y703147-ap4291911.html#ixzz2GpJGH7zB http://www.appliancepartspros.com" I have the Y703147 switch, and I am looking for replacements knobs for this switch. The current knobs, on their face, do look like 700855K, but, based on your post, these will not fit. Do you have a part number for the knobs that work with switch Y703147?
1 Answer Hello Jeff, The knob kit for unit would be part number 12200035 and would include 4 knobs. Read More...
Ellis November 04, 2012 for Model Number jenn aire model 629.2211280 I shorted out a control switch and am ordering a replacement. The switch has a red wire that connects it to a switch for an adjacent burner. There are clips on both ends of the wire, and one clip was damaged/burned. What do I need to order as a replacement wire, or should I purchase a suitable substitute at the hardware store?
1 Answer Hello Ellis! The part you are needing is the terminal, part number is TJMA02875-1. Thanks! Read More...
Linda September 23, 2011 for Model Number C202 Could you tell me which burner switch I need. My knob is a push to turn knob but it is not a D shaped shaft. Thanks
1 Answer Linda, the part number you supplied W11120795 is referred to as the figure 8 or double flat shaft, and the 700855K is referred to as the "d" shaped shaft. You stated your switch is not the "D" shaped shaft so you need to order W11120795. good luck and Thanks Read More...
Xnyer July 21, 2011 for Model Number Jenn Air C301 I need two stove top switches, Robert Shaw parts marked inf-240 p-977 203147 and the other marked inf 240p 871 201241. What replacement parts should I buy?
1 Answer Xnyer, You will need two(2) of each switch assembly W11120795 or 700855K . You will need to determine which switches you need based on the description or comparing the original switch to the pictures supplied here. Good Luck. Read More...
Carl May 28, 2011 for Model Number C201 Jenn Aire cooktop Are the four burner switches the same on model C201?
1 Answer Hello Carl. On model C201, all four burner switches are identical. The part you need is 700855K. I hope this info helps. Read More...