Bruce September 22, 2011 for Model Number LAT9334AAE Maytag washer will fill with water and then nothing,no sound at all what can the problem be?
1 Answer Bruce, You're on the right track, order and install a new lid switch assembly WP22001682 either one of the switches could be defective. Thanks and Good Luck Read More...
Kelly Mumm September 18, 2011 for Model Number taws700eq2 My washer will fill but does not stop on its own and eventually overflows. It also will not spin or drain. Does this sound like a lid switch problem?
1 Answer Hi Kelly. Remove power. Remove the back control panel. Remove the pressure switch hose and blow back into towards the tub. Did you remove any obstruction? You will replace the pressure switch part # is W10335056. If the hose is kinked it will also give this issue. Thank you. Read More...
Jason September 05, 2011 for Model Number 3949237 The Lid Switch Assembly came apart...I know it still works...but the spring fell out so I need a diagram showing how it looks from the inside when opened...so I know where everything is supposed to go...
1 Answer Hello Jason. Based on the information you provided, you will need to replace the lid switch 3949247V. The manufacture does not show a picture of how the switch is assembled, they only sell the switch as an assembly. Hope this helps. Read More...
Charlene G August 29, 2011 for Model Number lsr5132jqo whirlpool waher My washer fills with water runs with a cycle will agitiate, but when it time for the water to drain and to spin the machine stops.
1 Answer Hello Charlene. Based on the information you provided, you will need to test the lid switch 3949247V and see if it is bad. It should read closed with the lid closed. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Hello Sam. If the unit does not wash, fill, or spin, you will need to check and see if the lid switch 3949247V is bad and needs to be replaced. Hope this helps. Read More...
Tiffany August 17, 2011 for Model Number GE 10 CYCLE WASHER My washer fills up with water, but the water doesnt stop on its own. We have to manullay switch the cycle or it will over flow!! What part do I need??
1 Answer Hello Tiffany. Based on the information you provided, it sounds like the pressure switch is bad and will need to be replaced. Check and make sure the pressure hose is not broke or has come off. If it is good, you will need to replace the pressure switch. With a model number we can look the part up for you. Hope this helps. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Bonnie August 11, 2011 for Model Number Whirlpool My washer has stopped working. If I raise and lower the lid multiple times, it will eventually kick on. Does this sound like the lid switch?
1 Answer Hello Bonnie. Based on the information you provided, it sounds like the lid switch 3949247V or the lid strike is bad. Hope this helps. Read More...
Freda August 10, 2011 for Model Number 110-24422300 Tub will not spin when lid closes. I can make the tub spin by manually making contact with the switch. The plastic component on the lid no longer works. Which part do I order?
1 Answer Hello Freda. Based on the information you provided, you will need to replace the lid switch 3949247V. Hope this helps. Read More...
Carolyn August 08, 2011 for Model Number LSL9244EQ0 My washer will not advance to the next cycle. I have to manually turn the knob. Does this sound like a bad timer or lid switch?
1 Answer Hello Carolyn. If the washer works in all cycles, but needs to be advanced, it sounds like the timer WP3951703 is bad and will need to be replaced. Hope this helps. Read More...
James August 07, 2011 for Model Number Whirlpool Ultimate care 2 I moved my washer to clean behind it today. When I moved it back and ran it through a wash cycle it agitated fine but would not drain or spin. I checked the lid switch with an Ohm meter and it is fine. What else could it be ?
1 Answer Hello James. Check and make sure the strike for the lid switch 3949247V is good, and it is plugged in good. We will need your model number to help you more with this. Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...