Luna December 19, 2011 for Model Number Model LSR7233EQ0 Can I use a lid switch assembly from a Whirlpool Model LA5100XTW1 to replace the one in my current Model LSR7233EQ0?
1 Answer Hello Luna. Yes, based on the model number you provided, 3949247V is the correct lid switch assembly. Hope this helps. Read More...
Bob December 05, 2011 for Model Number LTE5243DQ5 Washer is a thin twin that stops mid cycle. When pressure is applied downward on lid it will sometimes start. I assume the lid switch is bad. What is the part number? It has two visible screws on top in rim of basket.
1 Answer Hello Bob. Based on the model number, WP3355806 is the correct lid switch assembly. Hope this helps. Read More...
Marcos December 03, 2011 i have a kenmore 700 washing machien they changed the timer a few months ago was working good but now starting doing something wrong, fills the water, starts washing, but it does not drain the warter when the timer is finished it is full of water but if I stay there I hear the noise when is time to rinse, I push the timer in and pull it back out and it works fine, but I have to be there to do that. thanks
1 Answer Marcos, There are a couple of possibilities,based on your post description. The new timer has failed, not likely but possible. The air dome hose to the water level switch is kinked, twisted or blocked with debris. or the drain pump impeller has become loose on the drive lug and the unit does not drain properly. Thanks and Good Luck Read More...
Kitty November 19, 2011 for Model Number 17BJ120(4C) I have a washer from Costco. It is Kirkland by Whirlpool. This is the only model # available to identify my mahine. This lid switch assembly looks identical to the one I need to replace. Is there any way to cross-reference my model # to confirm that it is the correct part? Thank you
1 Answer Kitty, The model number you supplied is not correct, I was unable to cross reference any information. But here is a post from the AppliancePartsPros Repair Forum that should be quite helpful [http://forum.appliancepartspros.com/dishwasher-repair/8110-replacing-lid-switch-whirlpool-kirkland-washer.html] Thanks and Good Luck Read More...
Joe November 12, 2011 for Model Number Whirlpool LTE5243DQ How do I remove the cabinet to access the lid switch?
1 Answer Hello Joe. Disconnect the power to the unit. Remove the two screws in the back corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and replace the lid switch 3949247V. Reinstall in reverse order. Hope this helps. Read More...
Hubert October 06, 2011 for Model Number Kenmore Elite ##110 2808 1700 The machine will not lock and just hums. This is a top load washer.
1 Answer Hello Hubert. If the latch assembly WPW10619844 is humming and is not locking, you will need to replace the latch assembly. Hope this helps. Read More...
1 Answer Hubert, The part you listed is for a top load washer, and it sounds like your working on a front load washer, could you please supply a proper model number of the washer, so we can advise you properly. Thanks Read More...
1 Answer Hello Bob. Yes, based on the model number you provided, 3949247V is the correct lid switch. Hope this helps. Read More...
Eva September 30, 2011 for Model Number LTG6234DQ4 Which lid switch is good for my Whirlpool thin twin washer/dryer?
1 Answer Hello Eva! The lid switch used on the given model is part number WP3355458. Thanks! Read More...
Bruce September 22, 2011 for Model Number LAT9334AAE Maytag washer will fill with water and then nothing,no sound at all what can the problem be?
1 Answer Bruce, You're on the right track, order and install a new lid switch assembly WP22001682 either one of the switches could be defective. Thanks and Good Luck Read More...