Dave September 08, 2018 for Model Number MAH5500BWW while replacing the pump motor, I tightened what I first thought was loose mounting screws on the pressure switch. After looking closer, I believe that I tightened some adjustment screws. How do I get them back in adjustment?
1 Answer Dave,Unfortunately, there is no tech data on this issue. Those screws will affect your fill for the main wash and rinse cycles. You need to back them out a couple of turns and check your fills on wash and rinse until you get them dialed back in. Read More...
Bob October 04, 2017 for Model Number MAH5500BWW My Maytag Neptune washer doesn't seem to pump out and spin. Leaves enough water in the drum to sometimes spill over when you open the door. If you then put it on the just spin setting, it will pump out and spin just fine? Which leads me to believe that the pump itself is fine. Pressure switch??
1 Answer Hello Bob. You will need to check all the balance switches in the unit and make sure that they are good. Also, check the motor and motor board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Van December 08, 2014 for Model Number MAH5500BWW Is it possible that this pressure switch can start leaking water and need replaced. That is all I can figure is happening. Thanks, Van
Van December 05, 2014 for Model Number MAH5500BWW Can a pressure switch leak water? I purchased a rubber cap that is installed on the pressure switch because that is the area that the leaking water is coming from. I thought the water was coming from around the connected hose but that didn't work. I cant see the leak but it seems to be coming from the back side of the pressure switch. Thanks
1 Answer Van, A pressure switch would not be able to leak water. You will want to double check the hose to make sure that it sis not leaking.. Read More...
Edward May 02, 2014 for Model Number Mah7500aww My washer will not spin faster then 280 R.P.M. and does not pump all of the water out.
1 Answer Hello Edward, The unit will not spin if any water is left in the tub. This sounds like the unit either has a restriction in the drain hose either before or after the pump. It is not uncommon for the drain pump WP25001052 to be defective. Read More...
Schuyler May 13, 2012 for Model Number MAH7500AWW I ordered and recieved the recommended pressure switch,(Item Number: AP4027954 Manufacturer's Number: 22003728 Made by Whirlpool Read more: http://www.appliancepartspros.com/Appliance-Parts/whirlpool-switch--pressure-item-number-ap4027954.aspx#ixzz1ujmNvo3c http://www.appliancepartspros.com there is no provision/spade connector for the double green wire that my machine has. but, I noticed that, in the main connect, there is 2 extra tabs on the new P switch, where there's only 4 tabs on my old P switch, connect...? Do I need to put the green wires into the pig tail, so that it will plug into, where these 2 extra tabs are located? If so, what type of leads do I need, that will fit into the pig tail? or is there a nother pressure switch that has the external spade on it, for this double green wire? hope this makes sense? any help or info on how to hook this switch up would be appreciated. thanks
1 Answer Schuyler, What is the serial number of your washer, you may have orderred the incorrect part, depending. Series 10 thru 73 require 22002994, and series 74 and up require WP22003728, you may have the incorrect switch for your series number. As for attaching the double green wires to the terminals of the switch, NO, don't do it. Green wires are A UL required ground circuit, and will create a short in the switch if attached to the terminals, unless otherwise marked or labelled. There should only be four wires attached to terminals on the water level switch, blue to terminal 31, gray to terminal 11, brown to terminal 32 and yellow to terminal 12. You'll need to check the drain pump and area for a grounding lug/tab. Good Luick and Thanks Read More...
Randy A. December 08, 2011 My mah5500bww neptune front loader will not spin out. It'll turn one and then the other acouple of times then nothing more. The first time it did this I messed around with the little plastic switch on the bottom front of the tub. I took the two wires off snd on and pushed the switch up and down a couple of times then it spun out. But now it won't. Thanks
1 Answer Hello Randy. You will need to check and see if any of the wires going to the out of balance switches are broke. if so, it will cause the problem you are having. Also, make sure the balance switch WP22002044 is good on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mike November 16, 2011 for Model Number MAH5500BWW Initial failure was a "nd" (no drain ). I cleaned all drain lines and pump. Got 1 rinse cycle to start and verified pump was draining water but at the end "nd" came back on. I disconnected power and reconnected. Now if I try a new cycle I here door look and some noises (like solenoids) then door unlocks and nothing happens, cycle doesn't start.
1 Answer Hello Mike. Blow through the pressure hose and see if it is clogged. Then try it again. If the problem continues, replace the pressure switch WP22003728. Hope this helps. Read More...
Tom April 12, 2011 Model: MAH5500BWW SN: A5970606CV Style: Y7909226 Thanks, I shut off both, but the off switch is all that is necessary to stop the water
1 Answer Hi Tom, the correct pressure switch for your model and serial number will be part WP22003728. Thanks! Read More...
Tom April 12, 2011 for Model Number MAH5500BWW Recently my washer has started to overfill. When a cycle is started the washer begins filling as normal, but never stops. The water fills the tub completely and then begins to spray out at the bottom of the door under pressure until you stop it by shutting off the machine and the water. Any idea what the problem might be?
1 Answer Hello Tom. If you have to shut off the water to get it to stop coming in the machine, you will need a new water valve. If you can stop it by turning the machine off, you will need a pressure switch. We will need your serial number to find the correct part for you. Hope this helps. Read More...