Shannon September 28, 2012 for Model Number wfw9500tw01 Our washing machine was also displaying the f35 error code. We cleaned out the hoses and just purchased the new pressure switch from you, replaced it and it is still displaying the f35 error code! Help!!!!
1 Answer Hello Shannon. Blow through the hose and make sure all is clear. Also, remove the large hose from the tub and make sure nothing is in the large hose. If all is clear, and you still get the code, and the pressure switch is new, replace the main control board. Read More...
Ernesto M August 17, 2012 for Model Number Whirlpool Washer Model HDUN / Front Loader Steam Duet I too have the code F35 that comes up. You talk about cleaning out the pressure tube but you don't say where it is or how to get to it. Where is it? Thanks, Ernesto
1 Answer Ernesto, The air tube is the hose WPW10004260 that attaches to the water level switch WPW10415587. Disconnect the hose from the switch and blow in the end of the hose, there should be little or no resistance. You may also want to remove the lower access panel, and remove and check the drain pump filter and interior for debris and build ups inside the pump. Thanks Read More...
Marianne August 13, 2012 for Model Number 11047781701 Kenmore elite he5t. Our machine is showing a suds/f35 error codes. We did check for loose or clogged analog pressure sensor. Still getting error message what part needs to be replaced? Just the sensor? What is the correct part number and do I really need to have a tech come or can I replace it on my own?
1 Answer Hello Marianne. Based on the information you provided, it sounds like you need to order and replace the pressure switch WPW10415587 on the unit. Read More...
Eddie February 15, 2012 for Model Number 110.47781 700 I ordered pressure switch AP5264563. I removed the old switch but having trouble inserting the electric wire into new pressure switch. Help.
1 Answer Hello Eddie. Make sure you line the ridges on the plug up with the groves on the switch WPW10415587. Then you will press the plug onto the switch. It will only fit one way. Hope this helps. Read More...
Ace December 05, 2011 I have a kenmore elite HE5T front load washer and keep getting error code F21 witch I understand is a drain problem but I can get it to drian if I wait until I here the pump try to run and then blow into the drain line and then it will drain just fine any idea what part I need?
1 Answer Hello Ace. Based on the information you provided, the drain pump is bad and will need to be replaced. Hope this helps. Read More...
Nath981 December 05, 2011 for Model Number WFW9500TW01 F35 and/or SUD code.....Pull the hose off pressure sensor, blow into rubber tube and hear gurgling sound. Look into sensor tubing connector and see some bubbles. Blow into tubing and squirt electronic cleaner into sensor and it works a couple times, then need to do it again.Is the pressure sensor bad or is there another problem?
1 Answer Hello Nathan. It sounds like to much soap has been used and it has filled the pressure hose with suds. You will need to clean it out good and make sure there are no crack or holes in the hose. If all of this is good, and the problem continues, you will need to replace the switch WPW10415587. Hope this helps. Read More...
Jim November 16, 2011 for Model Number WFW9500TW01 I also have the suds and F35 problem, is there a chance that the switch is ok, and I just need to clear the line? Thanks
1 Answer Hello Jim. Yes, you can try blowing through the hose and make sure it is not clogged. If the code continues, you will need to replace the switch WPW10415587. Hope this helps. Read More...
Gary October 21, 2011 for Model Number MHWE500VW11 How do you replace the pressure switch AP5264563 and the steamer control W10157910?
1 Answer Hello Gary. You will need to disconnect the power and remove the screws across the back of the top panel and slide the top toward the back of the washer and remove the top panel. Once removed, you can access the pressure switch WPW10415587 and the steamer control W10172726. You will now be able to repair and replace the parts. Be sure and make sure to blow through the pressure hose and make sure it is clear. Hope this helps. Read More...
Brenda S. October 02, 2011 for Model Number WFW9500TC01 I also am having the SUDs and error F35 messages. I just want to make sure I order the right part as I am seeing the same thing everyone else is seeing about the Water level pressure switch. What is the part number for my washer?
1 Answer Hi Brenda. If any over soaping occurs, this code will show up (SUD's). The pressure sensor hose will "Fill" with suds or debris ans code a F-35. Remove the hose and blow back into the tub. If you "feel" any obstruction pushed back into the tub, then possibly with a few rinse settings, the pump will drain clear of any debris'. The pressure sensor is part # WPW10415587. It sends the code. Use front loader washer "Affresh" cleaning tablets to monthly clean the unit. Part # is W10501250. Clean dryer vent and vent cap / hood completely so you do not re-wash lint that plugs hoses and for overall added clean ability. Thank You. Read More...
James August 27, 2011 for Model Number 110.47789701 I too need the switch and just want to know if these are all the same part for the part number I have been given by different people/websites. W10156252,PS3497663 and AP5264563. My Kenmore Elite H5t model # is 110.47789701. If I purchase and it is not correct, can I return?
1 Answer Hello, if you need the water level switch located near the control board inside the washer it will be WPW10415587. This is the substitution for the original part number of W10156252. Thanks! Read More...