Jennifer May 28, 2013 for Model Number WFW9600TA01 When we start our washer it goes to suds and then f35 what could be the problem? Sometimes it goes to f21 also.
1 Answer Hello Jennifer. Based on the information you provided, either the pressure switch or the pressure hose is bad on the unit. Blow through the hose and make sure it is not clogged and there are no cracks or breaks. If the code continues after that, replace the pressure switch on the unit. Read More...
Jennifer May 28, 2013 for Model Number WFW9600TA01 Where is the pressure switch located in the washer?
1 Answer Hello Jennifer. The pressure switch WPW10415587 is located under the top panel on the right hand side. You need to remove the top panel and you will see it on the right. Read More...
Jean & Howard May 08, 2013 for Model Number WFW9600TW00 Struggling with F20 error code. Checked that all filters, hoses, air hose, pump filter, pump, door gasket are clean and clear. No siphoning problem because drains to laundry tub next to washer. Replaced the analog pressure switch but still getting F20. Please help! Will replacing water valves and/or water flow regulator help? How can tell if CCU is going bad?
1 Answer Hello Jean & Howard, The tech sheet says this about the F20 fault code: If after 30 seconds not minimum 0.1l of water entered or maximum fill time of 13 minutes is exceeded, the valves will be turned off and the error code will be displayed. Press PAUSE/CANCEL twice to clear the display. Possible Causes/Procedure If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Verify inlet valve operation. If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. Unplug washer or disconnect power. Verify there is not a siphon problem. Verify wire harness connections to inlet valves, pressure switch, flow meter, and Central Control Unit (CCU). Check all hoses for possible leaks. Plug in washer or reconnect power. Verify pressure switch operation. Verify flow meter operation by blowing air through the part and measuring the resistance. Verify CCU operation by running a Diagnostic test or any cycle. I have found that the flow meter fails very commonly. I would be very skeptical of it. As for your last question, the CCU is tested by running a diagnostic test. This is done as follows: Starting Error History, Software Versions, and Diagnostic Test: NOTE: Washer must be empty and the control must be in the OFF state. Close the door. Select any one key (except “Stop/Cancel and Control Lock (EOC)) and follow the steps below, using the same key: Press/hold for 2-5 sec Press/hold for 2-5 sec Press/hold for 2-5 sec Press/hold for 2-5 sec Press/hold for 2-5 sec. Upon release, all yellow/green console LED lights will turn ON for 5 sec. If there are any failure codes stored by the washer the display shows them. Note: the last 4 errors will be displayed. Press the same key to advance to the next code. After the indication of error codes, the UI, CCU and MCU SW version will be displayed. The number of cycles since last clean washer cycle is displayed. All green console LED lights will turn ON for 5 seconds. Next washer begins the automated diagnostic test. To cancel out of service mode press “stop” button. Read More...
Renato December 17, 2012 for Model Number 11047789701 I have a kenmore elite with a lnt and f35 error code I clean the pump, run washer magic cleaner and I checked pressure sw. hose. Im planning to buy the pressure switch any suggestions from you do I have to check someting else.?
1 Answer Hello Renato, If pressure hose is fixed correctly, airtrap is not blocked and hose is not blocked then the issue would be the analog pressure switch and would need to be replaced. Read More...
Sam November 04, 2012 for Model Number W10133484A What type of pressure switch do I need for this model? W10133484A
1 Answer Hello Sam. Sorry, but the model number you provided is not working. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Laura October 29, 2012 for Model Number WFW9600TA00 I have a Whirlpool Duet Steam Model # 9600TA00 washer that "suds" then F-35 codes constantly. I've blown back in the rubber tube to the pressure switch without any results and drained and clean the drain in the bottom. Which pressure switch do I need to purchase and where can I get it? Whirlpool Duet Steam Model # WFW9600TA00.
1 Answer Laura, the analog pressure switch used on model WFW9600TA00 is part number WPW10415587. This part is available for purchase with our company. Thanks! Read More...
Selam October 29, 2012 for Model Number WFW9500TC01 I have Whirlpool Duet washer that is showing Error codes F35 and F27. I dont know what part I need change.
1 Answer Hello Selam, Error Code F27 indicates an overflow condition in which there is too much water or foam in the machine. Overflow contact on the pressure switch is closed. Check the drain for clogs and that it is not kinked Also check the pump for obstructions or clogs. F35 error code indicated analog pressure switch WPW10415587 failure. Ensure pressure hose is affixed properly, that the air trap is not blocked and that the hose is not blocked. If all this checks ok you will need to replace analog pressure switch. Read More...
Jimmy October 29, 2012 Sud shows then F35 error code when Whirlpool washer is turned on. Can you tell me what part looks like that I need?
1 Answer Hello Jimmy, F35 error code on some models indicate that the analog pressure switch is bad. Check your hoses to the pressure switch to ensure good connection, that hose is not restricted and air trap is not restricted. With the model number we would be able to provide more information on you unit. Read More...
James B. October 22, 2012 for Model Number Maytag Atlantis Hello. I have a Maytag gas dryer. I know the model is Atlantis and that it is about 10 years old. Recently, the pull knob to start the dryer has been harder to pull and activate the dryer. As of yesterday, when I pull on the knob, the lights to the left indicating wet or dry come on, but the dryer does not. When I let the knob go, the lights go out. I was wondering if that problem sounds like the on off knob or switch, and if so, is that something you sell on your website? Thanks for your time.
1 Answer Hi. Inside the dryer door frame is the model # so we can send the correct part. It sounds like a timer issue. If you have a MDG508... model # then the timer part # is WP37001241. If you have the MDG5000... model # then the timer is part # WP33001624. Thank You. Read More...
Jamie October 07, 2012 for Model Number WFW9600TW01 I have a Duet washer that "suds" then F-35 codes constantly. I've blown back in the rubber tube to the pressure switch without any results. Which pressure switch do I need to purchase and where can I get it?
1 Answer Hell Jamie, for the correct pressure switch for this model number you will need to order part number WPW10415587. Thanks! Read More...