Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Thermal Fuse by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM9345567
Manufacturer Part Number: 675813

The Thermal Fuse is an OEM part for Whirlpool dishwashers. It serves as a crucial safety component that prevents the appliance from overheating by cutting off electrical power if the temperature inside the dishwasher becomes too high. This helps protect both the dishwasher and your home from potential fire hazards.

Causes of a bad thermal fuse can include overheating due to blocked air vents, malfunctioning components that lead to excessive heat, or electrical surges that damage the fuse. Over time, regular wear and tear can also contribute to the fuse's failure.

Symptoms of a bad thermal fuse include:

  • The dishwasher not starting or running
  • The control panel not responding
  • The dishwasher stopping unexpectedly mid-cycle
  • No indicator lights or sounds when attempting to operate the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

More
$51.62

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Thermal Fuse (Part Number: OEM9345567)

1 Answer

Loren,

You will want to check the door switches to make sure that they have continuity when pushed in. If there is continuity then they are good. If this checks ok then the issue will be the control panel.

Read More...

1 Answer

Hello Brandon,
You should run a diagnostic cycle to help pinpoint the issue. Pressing the following option keys in the sequence shown will start the Diagnostics Cycle: HIGH TEMP WASH ? HEATED DRY ? HIGH TEMP WASH ? HEATED DRY
OR
POWER SCOUR (HIGH TEMP SCRUB) ? HEATED DRY ? POWER SCOUR (HIGH TEMP SCRUB) ? HEATED DRY
This will help to pinpoint the cause of the issue and is fully explained on the tech sheet behind the kickpanel.

Read More...

1 Answer

Don,

The unit can most likely be repaired but we would need to have the model number to be able to assist properly. The issue could be a burnt out element which sounds more likely or could be a bad control board. If you could supply the model number we would be able to assist properly. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx

Read More...

1 Answer

Hello Larry,
The fuse is blown by excessive current flow. For this reason, the technician should have done some tests to determine if the issue is with the unit or in the wiring to it. You see, if there is excessive current flow at the fuse, there is excessive current flow in the entire circuit, including the breaker and the wiring to the unit. It is a common failure for a motor winding to short and cause this but it is just as common to locate a burned wire nut or a bad breaker that can cause the same issue.

Read More...

1 Answer

Hello Dale. Make sure the float is not stuck. If not, replace the control panel WP3385741 on the unit. It sounds like it may be bad.

Read More...
Atx for Model Number Whirlpool DU941PWKQ1

Not all of the buttons on my dishwasher will function. Whirlpool DU941PWKQ1. The Rinse button appears to work, and the Pots and Pans cycle button works, but none of the other wash cycles will function properly. Cancel/drain appears to work. Most of the other buttons will neither work nor light up. When I hit Normal Wash, the sani rinse and cancel drain buttons light up and won't turn off. The Normal wash button doesn't cause the actual wash cycle to start; I think it just goes into drain mode (although there is nothing to drain). I'm stuck using a lot of water and energy because only the Pots and Pans wash cycle will work. Any ideas what is causing this or how to fix it? I'd like to be able to use light wash and normal wash again. Thanks.

1 Answer

Hello ATX. You need to order and replace the control panel on the unit based on the information you provided.

Read More...

1 Answer

Hello Leon. Based on the information you provided, you will need to order and replace the console 8275206 on the unit.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google