Bradley January 19, 2017 for Model Number MVWC7ESWW0 When I select a wash mode the machine starts to wash immediately. And at the end of cycle it will not spin out, in certain modes. I can hear the timer working, but it seems to not be aligned like it should be. Thank you for any help that is forth coming!
1 Answer Hello Bradley. You will need to replace the timer WPW10243947 and control WPW10104800 to repair the unit. Read More...
Jason July 11, 2016 for Model Number MVWC6ESWW1 My washer goes directly to spin cycle when it's turned on (with no water) and then stops after a couple of minutes.
1 Answer Hello Jason. If you set the timer on a wash cycle and it spins out, you will need to order and replace the timer WPW10243947 on the unit. Read More...
William March 16, 2016 for Model Number MVWC6ESWW I am replacing the timer on this machine and I am having trouble getting the old timer off. I have the knob off, but I can't see anything holding the timer to the machine.
1 Answer Hello William. Once you reach the timer, there is a clip you lift up and slide the timer over to remove the timer from the control panel. Read More...
Gayle G February 27, 2016 for Model Number MVWC6ESWW0 My washer seems to stick on the first rinse cycle and will not advance to the spin cycle. If the timer is moved to the extra spin cycle the washer will complete the load. Is this the timer behind the knob?
1 Answer Gayle, The most likely cause for the issue that you are having would be a faulty load sense switch WPW10292584. Read More...
Ricardo O. February 20, 2016 for Model Number Maytag I changed the Maytag Washer timer, but the Machine is still doing only the spin cycle > What else can be the problem? Thanks for you help. Ricardo
1 Answer Ricardo, Normally, this would be a timer issue, Recheck and make sure you wired the replacement timer properly. Check and make sure the fuse on the lid switch assembly or the switches aren't shorted or damaged. Some Maytag washer have a fuse and double switch, if the switch or fuse has failed, the washer wont fill and agitate. A model number would be a big help. Otherwise it could be a faulty motor, but that's not likely at this point. Read More...
Jay January 26, 2016 for Model Number MVWC6ESWW1 I have had my washer about 4 years ever sence it was installed it would shake or vibrate in extract or spin it will dance across the floor but now it will fill but nothing after that unless I move the dial please advise thank you
1 Answer Hello Jay. If you can manually advance the timer and it works, then it sounds like the timer is bad and will need to be replaced on the unit. Read More...
1 Answer CSwish, Unfortunately the manufacturer does not supply any information on the spin rate of the washer. It would most likely be around 550 to 700 RPM but we do not have information to elaborate on it. Read More...
Darlene May 08, 2015 for Model Number MVWC6ESWW1 My washer doesn't fill up with water, but well spin on the spin cycle. Is this my timer? I had this problem four years ago, but can't be for sure that it was the timer that was replaced. Thank you
1 Answer Darlene, It could be a timer issue, but you'd want to check or replace the water level / water temp. switch WPW10248240 and air tube first. You'd also want to check the wires between the water switch and the delay control board WPW10104800 on the back of the timer. your switch and wiring could be producing false information to the delay board, causing the washer to not fill and wash. Read More...
Kelly March 19, 2015 for Model Number MVWC7ESWW0 Washer doesn't start to fill with water when cycle started and starts agitating or spinning first. Sometimes starts to fill with water and begins to agitate while filling. Should the timer be replaced in this situation?
1 Answer Hello Kelly. You will need to order and replace the temp switch WPW10248240 and the timer WPW10243947 on the unit. Read More...
Randy February 05, 2015 for Model Number MVWC6ESWW1 My washer starts to agitate right away at start as it is filling up, then at the end of spin cycle it fills with about an inch of water before stopping.
1 Answer Hello Randy, This is usually caused by a stuck set of contacts in the pressure switch WPW10248240. Read More...