Joe November 13, 2017 for Model Number AGD4675YQ0 I have an Admiral Gas Dryer and noticed that it takes a couple cycles to dry my clothes on the timed cycle. I researched it a little and found out that I might need the primary and secondary gas coils. It didn't look like a hard thing to fix until I took the dryer apart. I couldn't remove the coils because there wasn't any type of bracket holding them on. The screws on the Gas valve were very odd looking because I couldn't get the right screw driver to fit it because there seems to be something in the center preventing any type of insertion. Can the coils be replaced on this type of gas valve? If so how can it be done without damaging the gas valve? Or does the whole gas valve have to be replaced? There is no gas smell and it does fire up. Just not as often as it should. Thanks for your expertise. Joe
1 Answer Joe, The gas valve coil assembly WPW10328463 is available, and in stock. To replace the coils, you need to remove power to the dryer and turn off the gas supply. Raise the top panel and remove the front panel. Use a short"stubby" phillips head screwdriver, remove the two small screws that attach the top bracket to the gas valve body, lift the bracket off the valve, lift the coils off the valve body plungers, revrese the procedure and test the dryer for heat and operation. Read More...
Quinten August 04, 2017 for Model Number KGYS750GQ1 New igniter cycles, just like the old one did. Gas valves open, with 2 new coils installed, just like it used too. Dryer gas, mostly, does not ignite as igniter times out ,,, but the gas keeps flowing . I can smell it and light it. Then occasionally the machine appears to cycle normally and the gas does light. Checked for lint blockage, there is none. Replaced the igniter and coils, still no joy, where do I go from here?
1 Answer Quinten, You will want to check the burner assembly to make sure that the ports on the burner are not clogged up and make sure that there is not rust on the burner. If this checks ok then the most likely cause, especially if gas keeps flowing when the igniter is going out then will be a gas valve issue. Read More...
R.J.F. May 19, 2017 for Model Number LG6881XSW1 The dryer turns on but does not heat. The igniter glows and turns off. No flame. I checked the solenoids with an ohm meter and they appear to be within limits. I didn't see the valve stems moving though. How do I know the problem is the gas valve? It is an expensive part not to sure of. Can I manually depress the 2 valve stems after the igniter glows and see if gas flows?
1 Answer Hello R.J.F., Tampering with the gas valve is not advisable. If the ignitor is glowing red or orange it is not pulling a strong enough current to open the gas valve. The ignitor should glow yellow to white hot for the electromagnetic field to be strong enough to open the gas valve. If it is not glowing in this manner, replace the ignitor 279311. If it is, the only alternative is to replace the gas valve 279923 if the coils are testing good. Read More...
Wayne March 26, 2017 for Model Number WGD4800XQ1 Gas ignites but goes off in about 30 seconds. Drum keeps turning. If I stop and start immediately, igniter starts to light up, but shuts down in about 3 seconds. If I wait to restart about 30 second, gas lights and goes out in half a minute, like before
1 Answer Wayne, You will first want to check the venting of the unit from the blower wheel to the outside of your home. If this checks ok then the most likely cause of this issue will be faulty gas solenoids which would be part number 279834. Read More...
Donna April 07, 2016 for Model Number RGL463BW1 The timer needs to be changed so it will go onto the next cycle so when in no heat/fluff you could smell the gas when I opened door. Shut off gas What's the problem?
1 Answer Hello Donna. You will need to check the dryer vent and make sure it is venting properly. Also, make sure the flame is lighting and working properly. Read More...
Donna August 01, 2015 for Model Number GGW9250PW3 I have the part removed. How do you install the new valve? The service manual makes no mention on installing the valve.
1 Answer Donna, If you have removed the water valve, you would install it in reverse. Just following the instructions in reverse. Read More...
Victor July 20, 2015 for Model Number LGB6200PQ0 Dryer doesn't turn off until I open the door and also it starts to heat up in the beginning then it's cool for the rest of the cycle . Thanks guys!
1 Answer Hello Victor. For a no heat issue, it can cause the timer not to advance and turn off. Try fixing the no heat and see if the timer starts working. If not, replace the timer. For the no heat issue, You will need to test the thermostats and the flame sensor and make sure they are good. They should read closed for continuity. Also, check the igniter to see if it is good. If it is not glowing, test for power. Here is a link on how to use a multi-meter for the testing procedures. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jesse July 05, 2015 for Model Number MGDC200XW2 My dryer doesnt have heat. Also the timer stopped working as well. I replaced Igniter, however the new one Isn't working. What can I do to fix this issue?
1 Answer Jesse, With the heat and the timer not working, this would appear to be a issue with the timer on the unit. The contacts in the timer are not making to allow the heater to come on and it sounds like the timer motor may be bad. Read More...
Bob K. December 19, 2013 for Model Number GGW9250PW3 Model: GGW9250PW3 Type: BADT-NAT-1206006-EL20 I smell gas! I have shut off the gas line to the dryer. The dryer is probably older than 5 years. Does this model have a history showing a likely component to develop a leak?
1 Answer Hello Bob, This unit has as high a likely hood of a gas leak as any other gas unit out there. I would make up a gas leak solution by putting one teaspoon of liquid soap, (or a little less), to a quart of water and spray it on the gas lines. If there is a leak and the solution is no thicker than that, it will produce a little pile of bubbles at the leak. Read More...
Tim L March 13, 2013 for Model Number Whirlpool lg7011xsw0 Dryer works fine and timer advances if you use in minutes to dry mode. If you use the regular or permanent press cycles the timer will not advance and clothes do not dryer. Have swapped out the coils and the timer with no luck. At a bit of a loss on this one...
1 Answer Tim, Your going to need to check and clean the exhaust vent and vent hood, check and remove any debris from the blower housing and internal exhaust pipes and check the tumbler seals for tears and holes. Once all's checked then consider the regulating thermostat WP694674 and the hi limit switch 279048. The way this dryer operates on an "auto cycle" The proper temperature has to be maintained, if there is an air flow problem or the thermostats "open" before the temperature is reached, the timer will not advance. In timed dry, the timer operates for the selected amount of time, wether the clothes dry or not. Read More...