Parts for Broan RME5030SS: Range Hood Assembly Parts

This replacement power module regulates and distributes electrical power within the unit, restoring proper fan and light operation when the original module fails.

• Controls power to the fan and lights for consistent performance
• Helps resolve issues like no power, fan not running, or lights not working
• Maintains safe operation by replacing a failed or shorted module
• Designed to fit the original location with existing connectors

• Disconnect power before servicing; capacitor and components can hold a charge
• Note wire and connector positions; take photos for reference
• Handle the board carefully; avoid static discharge and flexing the circuit
• Inspect harnesses and switches for heat damage before reassembly

This replacement lens covers the light on your range hood, diffusing brightness and protecting the bulb from grease and debris. Restore clean light output and a finished look when the original lens is cracked, yellowed, or missing.

• Covers and diffuses the hood's light for even illumination
• Shields the bulb from grease, moisture, and splatter
• Replace if the lens is cracked, warped, yellowed, loose, or missing
• Helps reduce glare and hot spots caused by a damaged or absent lens

• Disconnect power to the hood before servicing
• Allow the bulb to cool completely
• Support the lens while releasing tabs, clips, or screws; note orientation for reinstallation
• Do not force; if resistance is felt, verify the retaining method for your model

This Heat Sentry is a thermal sensor that detects excessive heat in the hood and helps protect the appliance by triggering a shutdown or alert when temperatures rise above safe levels. It restores proper heat-sensing function for safety. What it does:

• Monitors hood temperature and responds if heat exceeds safe thresholds
• Trips the hood's thermal protection to stop the blower or signal an overheat condition
• Helps prevent damage from prolonged exposure to high heat while cooking
• Common symptom: hood fan stops running or won't restart after heavy cooking, or thermal protection repeatedly trips

• One Heat Sentry thermal sensor

• Turn off power at the breaker before accessing the hood or wiring
• Installation typically requires removing the hood canopy or control panel to reach the sensor
• Match mounting and connector type to your unit; replace only with the same part number

This control box is the electrical control module that manages a range hood's fan and lighting functions, restoring reliable power and speed control for ventilation performance. What it does:

• Provides the main electronic control for fan blower speeds and integrated lighting
• Receives inputs from hood switches or remote and switches power to motors and lights
• Replaces a failed or intermittent control module that causes unresponsive or erratic blower/light operation
• Prevents electrical faults caused by damaged or burned-out control circuitry

• Disconnect all power to the appliance before starting any work
• Replace only with the exact part number for your unit
• Follow manufacturer wiring diagrams and secure all connections; use proper connectors/insulation

This blower wheel spins inside the vent blower assembly to move air through the hood or ventilation system, restoring proper airflow and helping clear smoke and cooking odors. Fits applications that use a single replacement wheel. What it does:

• Replaces worn or damaged wheel blades that reduce airflow
• Restores proper ventilation when airflow is weak or uneven
• Can reduce vibration or scraping noises caused by a bent or broken wheel
• Works with the blower motor to circulate air through the ductwork and filters

• Disconnect power to the appliance before beginning work.
• Handle with care — blower housings and mounting screws may have sharp edges.
• Verify wheel orientation and secure mounting to the motor shaft per manufacturer alignment marks.

Replacement mounting washer that secures fasteners and maintains proper spacing on blower, motor, and housing assemblies. Restores alignment and helps reduce vibration and rattling caused by loose or missing hardware. What it does:

• Provides a smooth bearing surface under a screw or nut to distribute load and prevent pull-through.
• Keeps mounting fasteners aligned and helps maintain correct spacing between components.
• Helps reduce vibration and noise from loose or worn hardware when installed properly.
• Useful when replacing corroded or damaged fastening hardware during routine repairs.

• Disconnect power to the appliance before beginning any repair.
• Match the washer to the original part (size and thickness) and install between the fastener head and the mounting surface.
• Do not overtighten fasteners—tighten just enough to secure the part and avoid crushing the washer.
• Replace any rusted or damaged screws, nuts, or complementary hardware for a reliable repair.

This damper assembly helps control airflow by opening during operation and closing when the fan is off, reducing backdrafts and outside air intrusion. Replacing a worn damper restores proper ventilation and helps keep kitchen air moving the right way.

• Opens to let exhaust air out; closes to block drafts when the unit is off
• Can help address rattling, flapping, or poor airflow due to a stuck or broken damper
• Designed for compatible ventilation units that use this specific damper style

• Disconnect power before servicing
• Access damper at the duct connector or discharge outlet; note orientation of the flap
• Inspect and clear debris from the duct path before installing
• Verify smooth flap movement after installation and restore power to test

This cable stop is a small retaining part that secures a control or cable assembly to the hood/chassis, helping keep cables routed and fastened so controls operate smoothly. It's a simple, replacement fastening piece. What it does:

• Holds and secures a control or actuator cable in place to prevent slipping or disconnection
• Helps maintain correct cable routing so controls and dampers move reliably
• Can eliminate slack or catching that causes loose or intermittent control action
• Commonly used where a cable exits a chassis or attaches to a lever or linkage

• One cable stop/retainer

• Disconnect power to the appliance before gaining access to internal components
• Remove the exterior cover or access panel to reach the cable attachment point
• Reattach the cable into the stop and verify proper routing and tension; test operation before reassembling

This bottom decorative flue piece finishes the lower section of a range hood flue, restoring the unit's appearance and helping direct the duct cover fit. It's a direct-fit exterior trim part used where the flue meets the hood. What it does:

• Replaces the lower trim section of the hood flue to restore a clean, finished look
• Helps align the flue cover with the hood body for a proper exterior fit
• Addresses issues like a missing, dented, or cosmetically damaged bottom flue piece
• Works with the flue assembly to maintain the intended visual profile of the hood

• One bottom decorative flue piece as pictured

• Basic hand tools typically required; follow hood manufacturer instructions
• Remove power to the hood/light/fan before beginning any disassembly
• Handle painted or plated surfaces carefully to avoid scratching; support the flue during removal/installation to prevent bending

This decorative flue top is the upper trim piece that covers and finishes the exposed flue/chimney on compatible range hood assemblies, restoring a clean, finished look and helping keep grease and dust out of the flue area. What it does:

• Covers and conceals the exposed flue/chimney pipe for a finished appearance
• Helps keep grease, dust and debris from collecting in the flue opening
• Secures to the hood's flue assembly to reduce visible gaps and looseness
• Useful when replacing a damaged, dented or worn flue top that affects appearance

• Follow the hood manufacturer's instructions and shut off power to the appliance before starting work
• Some installations may require two people to lift and align the flue top safely
• Use appropriate hand tools and avoid scratching the finish during installation
• Verify proper fit to your specific hood flue assembly before final fastening

This metal mounting bracket secures range hood components in place to restore proper alignment and support. It replaces a damaged or missing bracket so parts sit securely and the hood operates without rattling or sagging. What it does

• Provides structural support for hood components and assemblies
• Restores proper alignment to reduce vibration and noise
• Helps maintain correct airflow by keeping parts positioned
• Common fix for loose, bent, or broken mounting points

• Basic hand tools required; for exact fastener locations
• Turn off power to the appliance before accessing internal parts to avoid injury
• Inspect nearby hardware and replace any stripped screws or damaged mounts for a secure fit

This electronic control board replaces the failed main control in a range hood to restore fan, light, and timed functions. It provides the appliance's switching and control logic so the hood responds correctly to user commands. What it does:

• Controls fan speed selection and on/off signaling for the range hood
• Manages light operation and any timed or delay functions
• Re-establishes reliable electronic switching when the original board has failed
• Common symptoms: hood won't power on, fan or lights are unresponsive, or operation is intermittent

• Disconnect power at the breaker before starting any work
• Handle the board by its edges and avoid static discharge or contact with circuitry

This mounting bracket secures interior components and helps stabilize the appliance's assembly for reliable operation and reduced vibration. It replaces a worn or broken support bracket to restore proper fit and alignment. What it does:

• Provides a secure attachment point for cabinet/hood or internal assemblies
• Stabilizes panels and components to reduce rattling or movement
• Helps maintain correct alignment of the unit's parts for normal operation
• Prevents further wear caused by loose or shifted components

• Disconnect power to the appliance before beginning any work.
• Use the original screws or OEM-recommended fasteners; confirm screw size before installation.
• Inspect mating surfaces and replace any damaged hardware or stripped threads.

This replacement lens covers and protects the light on compatible Broan range hoods, restoring the fixture's finished appearance and even light diffusion. Durable plastic shields the bulb and helps prevent direct contact. What it does:

• Covers and protects the hood light fixture from grease, spills, and impact
• Diffuses light for more even illumination across the cooktop
• Replaces cracked, discolored, or missing lenses that cause glare or exposed bulbs
• Helps maintain a clean, finished look for the underside of the hood

• Disconnect power to the range hood before starting any work to avoid electrical shock.
• Usually installs by snapping into place or fastening with a small screw—handle gently to avoid cracking.
• Use a soft cloth and mild cleaner; avoid abrasive cleaners that can scratch the lens.

This push button is the user-facing control that operates a range hood or ventilation control panel, restoring tactile on/off and speed/light selection for worn or broken buttons. It provides a simple, direct way to make the control responsive again. What it does:

• Replaces a worn, cracked, or missing control button so the switch beneath can be pressed reliably
• Restores tactile feedback for on/off, speed selection, or light control on compatible vent hoods
• Helps eliminate sticking, intermittent contact, or lost button functionality
• Simple cosmetic repair that returns the control panel to usable condition

• Disconnect power to the appliance before attempting any repair to avoid shock
• Remove the vent hood trim or control panel per the appliance service instructions to access the button and switch
• Gently pry or unclip the old button from the bezel; press the replacement onto the switch stem until it seats