Parts for Broan RMP17004: Range Hood Parts

This replacement charcoal/activated carbon filter helps reduce cooking odors in recirculating range hoods and microwave-hood combos. It restores odor-absorbing performance without modifying your appliance. What it does:

• Adsorbs and helps neutralize cooking odors in recirculating ventilation systems
• Restores fresh air circulation when existing carbon filter is saturated or aged
• Helps reduce lingering smoke and food smells during and after cooking
• Compatible with recirculating (non-venting) hood setups that use a carbon filter element

• One charcoal (activated carbon) odor filter

• Disconnect power or follow appliance safety instructions before servicing
• Typically installs behind the grease filter or access panel; follow the appliance owner's manual
• Replace periodically or when odors persist despite clean grease filters
• Dispose of used carbon filters per local regulations

This capacitor helps start and keep the blower/fan motor running smoothly in your range hood or ventilation unit. Replacing a weak or failed capacitor can restore proper fan performance and reduce humming or slow-start issues. What it does

• Provides the phase shift needed for a PSC fan motor to start and run correctly
• Common symptoms of failure: fan won't start, only hums, runs slowly, or starts intermittently
• Physical clues include a swollen case or heat-damaged terminals

• 1 capacitor

• Disconnect power at the breaker before servicing; capacitors can retain a charge
• Safely discharge the old capacitor and avoid shorting the terminals
• Note wire positions/take a photo and transfer wiring to the new part one-for-one
• Mount securely and keep leads clear of sharp edges and hot surfaces; test operation after reassembly

This LED light bulb restores bright, dependable lighting in your range hood so you can clearly see the cooktop while cooking. It replaces the original lamp specified by the manufacturer for models that call for this part number. What it does:

• Provides task lighting from the hood's light socket
• Replaces a bulb that is burnt out, dim, or flickering
• Helps maintain clear visibility over the cooking surface
• Common symptoms include the light not turning on or intermittent operation

• LED light bulb

• Disconnect power to the hood at the breaker before servicing
• Allow the lamp to cool completely before handling
• Access the light from the underside; remove any lens or retaining ring as designed
• Remove the old bulb, seat the new bulb fully, and test before reinstalling the lens/trim

This Heat Sentry is a thermal sensor that detects excessive heat in the hood and helps protect the appliance by triggering a shutdown or alert when temperatures rise above safe levels. It restores proper heat-sensing function for safety. What it does:

• Monitors hood temperature and responds if heat exceeds safe thresholds
• Trips the hood's thermal protection to stop the blower or signal an overheat condition
• Helps prevent damage from prolonged exposure to high heat while cooking
• Common symptom: hood fan stops running or won't restart after heavy cooking, or thermal protection repeatedly trips

• One Heat Sentry thermal sensor

• Turn off power at the breaker before accessing the hood or wiring
• Installation typically requires removing the hood canopy or control panel to reach the sensor
• Match mounting and connector type to your unit; replace only with the same part number

This blower is the ventilation fan assembly that moves air through the appliance to clear smoke, steam, and cooking odors. Replacing a worn blower can restore proper airflow and reduce performance issues. What it does:

• Circulates air through the vent or hood to support proper exhaust performance
• Helps clear smoke, steam, and odors from the cooking area
• Restores reduced airflow caused by a damaged or failing fan assembly
• Reduces unusual rattling or vibration when the blower is the source of noise

• Blower assembly

• Disconnect appliance power before inspecting or replacing the blower
• Handle the fan wheel carefully to avoid bending blades or disturbing balance
• Verify electrical connections and mounting fit match the appliance before final assembly
• Refer to OEM instructions for model-specific removal and reinstallation steps

This blower wheel spins inside the vent blower assembly to move air through the hood or ventilation system, restoring proper airflow and helping clear smoke and cooking odors. Fits applications that use a single replacement wheel. What it does:

• Replaces worn or damaged wheel blades that reduce airflow
• Restores proper ventilation when airflow is weak or uneven
• Can reduce vibration or scraping noises caused by a bent or broken wheel
• Works with the blower motor to circulate air through the ductwork and filters

• Disconnect power to the appliance before beginning work.
• Handle with care — blower housings and mounting screws may have sharp edges.
• Verify wheel orientation and secure mounting to the motor shaft per manufacturer alignment marks.

Replacement mounting washer that secures fasteners and maintains proper spacing on blower, motor, and housing assemblies. Restores alignment and helps reduce vibration and rattling caused by loose or missing hardware. What it does:

• Provides a smooth bearing surface under a screw or nut to distribute load and prevent pull-through.
• Keeps mounting fasteners aligned and helps maintain correct spacing between components.
• Helps reduce vibration and noise from loose or worn hardware when installed properly.
• Useful when replacing corroded or damaged fastening hardware during routine repairs.

• Disconnect power to the appliance before beginning any repair.
• Match the washer to the original part (size and thickness) and install between the fastener head and the mounting surface.
• Do not overtighten fasteners—tighten just enough to secure the part and avoid crushing the washer.
• Replace any rusted or damaged screws, nuts, or complementary hardware for a reliable repair.

This damper assembly helps control airflow by opening during operation and closing when the fan is off, reducing backdrafts and outside air intrusion. Replacing a worn damper restores proper ventilation and helps keep kitchen air moving the right way.

• Opens to let exhaust air out; closes to block drafts when the unit is off
• Can help address rattling, flapping, or poor airflow due to a stuck or broken damper
• Designed for compatible ventilation units that use this specific damper style

• Disconnect power before servicing
• Access damper at the duct connector or discharge outlet; note orientation of the flap
• Inspect and clear debris from the duct path before installing
• Verify smooth flap movement after installation and restore power to test

This electronic control board replaces the failed main control in a range hood to restore fan, light, and timed functions. It provides the appliance's switching and control logic so the hood responds correctly to user commands. What it does:

• Controls fan speed selection and on/off signaling for the range hood
• Manages light operation and any timed or delay functions
• Re-establishes reliable electronic switching when the original board has failed
• Common symptoms: hood won't power on, fan or lights are unresponsive, or operation is intermittent

• Disconnect power at the breaker before starting any work
• Handle the board by its edges and avoid static discharge or contact with circuitry

This push button is the user-facing actuator that lets you start and stop a function on the appliance. It provides a tactile interface so controls respond reliably and the panel stays complete and usable. What it does

• Acts as the manual actuator for a control circuit when pressed.
• Restores missing, cracked, or non-responsive panel controls.
• Helps resolve symptoms like a loose button, no tactile feedback, or a snapped/missing cap.
• Works with the existing switch/mounting hardware to re-establish normal button operation.

• One push button

• Always disconnect power to the appliance before beginning service to avoid shock.
• Remove the control panel or cover per the manufacturer's instructions to access the button.
• Button may snap onto a switch stem or require a retaining clip; inspect existing hardware and transfer as needed.

This control board is the electrical module that operates the hood's fan and lights, restoring normal control when the original board fails. It replaces a faulty or unresponsive control module to regain reliable function. What it does:

• Receives user inputs and switches power to the fan blower and lights
• Re-establishes normal fan speeds and light control when the original board is defective
• Can stop intermittent or non-responsive fan/light operation caused by a failed control circuit
• Helps resolve symptoms such as no power to fan or lights, erratic operation, or unresponsive controls

• One control board (electrical control module)

• Disconnect power to the appliance at the breaker before beginning work
• Handle the board by the edges and avoid static discharge; use anti-static precautions if available
• Verify connector orientation and seating; match wire harness connectors to the same locations as the original

This replacement lens covers and protects the light on compatible Broan range hoods, restoring the fixture's finished appearance and even light diffusion. Durable plastic shields the bulb and helps prevent direct contact. What it does:

• Covers and protects the hood light fixture from grease, spills, and impact
• Diffuses light for more even illumination across the cooktop
• Replaces cracked, discolored, or missing lenses that cause glare or exposed bulbs
• Helps maintain a clean, finished look for the underside of the hood

• Disconnect power to the range hood before starting any work to avoid electrical shock.
• Usually installs by snapping into place or fastening with a small screw—handle gently to avoid cracking.
• Use a soft cloth and mild cleaner; avoid abrasive cleaners that can scratch the lens.

This factory hardware replaces worn or missing rings used in select Broan ventilation products. It helps secure and space components so they fit correctly and run more quietly, reducing looseness and vibration from fatigued hardware. What it does:

• Retains and spaces mating parts to prevent movement during operation
• Helps maintain proper alignment for smooth, quiet performance
• Restores a snug, rattle-free fit when originals are bent, worn, or missing
• Common signs it's needed: loose or rattling parts, poor fitment, visible damage, or a missing ring during service

• Replacement rings only

• Disconnect power at the breaker before servicing
• Note the original orientation and order of hardware; take photos for reference
• Use appropriate pliers (snap-ring/needle-nose); wear eye protection—small rings can spring free
• Inspect adjacent parts for wear and replace any damaged components to ensure a secure fit