Parts for Ge ZV1050SF2SS: 01 - Range Hood Parts

This pre-wired capacitor replaces the factory capacitor used to help start and stabilize appliance motors and controls. The attached lead wires make hookup straightforward for compatible appliance connections. What it does

• Provides the necessary capacitance to help motors start and run smoothly
• Helps stabilize electrical signals to reduce motor stalling or inconsistent operation
• Addresses humming, failure-to-start, or intermittent motor performance when the capacitor is faulty
• Used wherever a compact, pre-wired run/start capacitor is required by the appliance

• Disconnect power to the appliance before servicing to avoid shock or injury
• Capacitors can hold a charge; discharge safely
• Verify terminal style, polarity (if applicable), and electrical rating match the original part before installation

This is the interior/cooktop lamp bulb used in select GE microwaves. It restores proper lighting inside the cavity and/or over the cooktop so you can clearly see food while cooking and during cleanup.

• Provides illumination inside the microwave and/or for the cooktop task light
• A failed bulb can cause dim, flickering, or no light
• Helps you verify doneness and monitor cooking progress safely

• Unplug the microwave or disconnect power before service
• Allow the bulb and surrounding area to cool before handling
• Use clean, dry hands or gloves to avoid contaminating the bulb
• Replace access covers and secure fasteners before restoring power

Used to cover the control board

This connection air outlet is the OEM-style duct connector that directs airflow between the appliance and its venting path, restoring proper exhaust flow and helping reduce cooking odors and moisture build-up. What it does:

• Provides a secure pathway for exhaust air from the appliance to the vent
• Restores proper ventilation when the original connector is cracked or disconnected
• Helps reduce lingering smoke, steam, and odors caused by poor airflow
• Prevents air leaks that can lead to reduced performance or heat buildup

• Turn off power to the appliance before starting any repair
• Verify correct orientation and secure all fasteners or clamps to prevent air leaks
• Inspect adjacent ducting and seals; replace damaged components for best results

5 A, 125 V electrical fuse that restores circuit protection when the original fuse is blown. Replacing the failed fuse helps prevent further electrical damage and can restore normal appliance operation. What it does:

• Provides overcurrent protection for the appliance circuit to stop excessive current flow.
• Replaces a blown or open fuse that prevents the appliance from powering up.
• Common symptom: appliance has no power or a circuit/component won't operate.
• Common symptom: intermittent power or a fuse that visibly shows a blown element.

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing the fuse.
• Replace only with the exact rated fuse (5 A, 125 V) and part number to maintain proper protection.
• Do not bypass the fuse or use makeshift substitutes — that can cause fire or equipment damage.

A small adhesive MG logo emblem that restores the original appearance of your appliance. This peel-and-stick badge replaces a worn, faded or missing logo to keep the exterior looking factory-fresh. What it does:

• Cosmetic replacement for a missing, scratched or faded MG emblem
• Adheres to control panels, doors or trim where the original badge was located
• Restores brand identification and a finished appearance to the appliance
• Simple adhesive design avoids the need for fasteners or tools

• Clean and dry the mounting surface before applying to ensure good adhesion
• Peel backing and press firmly in place, aligning carefully before contact
• Avoid repositioning once attached; removal may damage the emblem or finish
• For safety, disconnect power before working near electrical controls or panels

This upper rack telescopic support secures and guides the dishwasher's upper rack so it glides smoothly in and out. Replacing a worn or broken support restores stable rack movement and helps prevent the rack from sagging or binding. What it does:

• Provides the sliding track/support for the dishwasher upper rack so the rack extends and retracts smoothly
• Keeps the upper rack aligned and supported during loading and unloading
• Commonly replaced when the rack binds, drops, or feels loose while pulling out
• Prevents further wear to rack rollers and side assemblies by restoring proper alignment

• One upper telescopic rack support

• Disconnect power and water supply before beginning any repairs
• Remove the upper rack to access and replace the telescopic support per the service diagram
• Use basic hand tools; avoid excessive force to prevent damage to adjacent components

This printed circuit is the appliance's electrical control board that manages timed functions and user commands, restoring responsive control and reliable operation when the original board fails. What it does:

• Controls and routes power to user interface, timers, and functional components
• Replaces a failed control board that causes unresponsive buttons or blank/display issues
• Restores correct timing and electronic control when the appliance behaves erratically
• Helps stop intermittent power loss or unexpected cycle interruptions linked to a bad board

• Disconnect power to the appliance before inspecting or replacing the board
• Handle the board carefully; avoid touching components or connector pins to prevent ESD damage
• Verify wiring and connectors match before final assembly; secure all connections

Replace a cracked or heat-damaged light socket base with this ceramic insulation base. It insulates and secures the lamp receptacle, helping the bulb seat correctly and maintain a reliable connection for consistent lighting.

• Provides a heat-resistant, insulated mounting point for the light socket
• Helps maintain a stable electrical connection to the bulb
• Common symptoms: light won't turn on with a known-good bulb, flickers, bulb won't seat securely, scorch marks or cracking at the socket base
• Restores reliable illumination when the original base is worn or damaged

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the area to cool completely before working near the lamp
• Handle ceramic components carefully; transfer any leads or hardware one at a time to maintain correct wiring
• Use the correct bulb type and wattage as specified by the appliance rating label

The Transformer is an OEM replacement part for GE range hoods. It is an electrical component responsible for regulating voltage levels both internally and to exterior control panels. Proper voltage regulation from the transformer ensures accurate function of hood features like lighting, fan speeds, and exhaust capabilities. 

Causes of a bad transformer typically involve degradation over extended use. Faulty wiring or damage from power surges are other potential causes.

Symptoms of a bad transformer include:

• Lights flickering or not turning on as intended
• Variable or inadequate fan performance  
• Control issues such as buttons not working reliably  
• Abnormal noises from electrical components

This genuine OEM GE part is compatible with GE Monogram and select Kenmore hood brands.

This ring nut is a small threaded retaining nut that secures a mating component to its shaft or connection, restoring a stable mechanical or sealed connection and reducing movement or leaks when properly installed. What it does:

• Holds a shaft, tube or fitting in place by threading onto the mating component
• Prevents components from working loose and reduces rattling or vibration
• Helps maintain a sealed connection where used on fittings or hose connections
• Useful when a stripped or missing nut causes loose hardware or intermittent operation

• One ring nut

• Disconnect power and shut off water before beginning work
• Inspect mating threads and replace if damaged; clean threads before installing
• Hand-start threads to avoid cross-threading, then tighten with appropriate tool; avoid overtightening

Solid-state triac that switches AC power under command of the appliance's electronic control board. Replacing a failed triac restores proper power control to heating elements or motors and resolves intermittent or no-power symptoms. What it does:

• Acts as a solid-state switch on the control board to regulate AC power to heating elements or motors
• Enables the electronic control to modulate output for temperature or speed control
• Failure can cause no heat, intermittent heating, or loss of motor control
• Designed to match the original control circuit; check board mounting and connections before replacing

• Always disconnect all power at the breaker or unplug the appliance before servicing — risk of electric shock
• This part mounts to the control board; handle the board and connectors carefully to avoid damage
• Use anti-static precautions when handling electronic components;
• Verify the part number on the original board before installation