Parts for Ge ZV855SP1SS: 01 - Range Hood Parts

The Grease Filter is an OEM part for GE range hoods. It is responsible for trapping grease and other particles from the air as it is drawn through the hood, helping to keep the kitchen environment clean and free of contaminants.  The filter measures approximately 9" x 16".

Causes of a bad grease filter can include clogging due to accumulated grease and debris, damage from cleaning or mishandling, and general wear over time that reduces its effectiveness. 

Symptoms of a bad grease filter include:

• Reduced airflow through the range hood
• Unpleasant odors lingering in the kitchen
• Grease buildup on kitchen surfaces
• Visible dirt and debris on the filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This pre-wired capacitor replaces the factory capacitor used to help start and stabilize appliance motors and controls. The attached lead wires make hookup straightforward for compatible appliance connections. What it does

• Provides the necessary capacitance to help motors start and run smoothly
• Helps stabilize electrical signals to reduce motor stalling or inconsistent operation
• Addresses humming, failure-to-start, or intermittent motor performance when the capacitor is faulty
• Used wherever a compact, pre-wired run/start capacitor is required by the appliance

• Disconnect power to the appliance before servicing to avoid shock or injury
• Capacitors can hold a charge; discharge safely
• Verify terminal style, polarity (if applicable), and electrical rating match the original part before installation

Used to cover the control board

This plastic screw visor is the small trim screw cover that protects and hides the fastener on appliance control panels and exterior trim. It keeps the appearance tidy and prevents dirt from collecting around exposed screw heads. What it does:

• Covers and conceals a panel or trim screw to restore original appearance
• Protects the screw head from dirt, moisture and accidental contact
• Helps maintain a finished look on control panels, bezels and exterior trim
• Commonly used where small plastic caps are needed to match factory styling

• Simple push-on or snap-fit installation; press into place over the screw head
• Use standard hand tools to access screw; disconnect power to the appliance before servicing
• Replace any damaged surrounding trim clips or screws for secure fit

A replacement glass visor that restores the finished front trim and protective cover on compatible GE appliances. Replaces a cracked or damaged front visor to improve appearance and protect underlying components. What it does

• Covers and protects the appliance's front/control trim area from spills, grease and impact damage
• Restores the appliance's finished look when the original visor is cracked, chipped or cosmetically worn
• Keeps underlying controls and components shielded from debris that can affect operation
• Fits as a direct-fit cosmetic/trim piece when the matching part number is required

• One glass visor

• Turn off and unplug the appliance or disconnect power at the breaker before starting
• Handle with care—wear gloves and eye protection; glass edges can be sharp
• Use only the matching OEM part number for correct fit and to avoid damage

This charcoal filter set restores odor removal for ductless range hoods. In recirculating mode, the carbon media adsorbs cooking smells and smoke so your kitchen air stays fresher and the hood performs as intended.

• Traps odors and smoke during recirculating operation
• Helps maintain airflow and ventilation performance
• Replace when saturated or damaged to keep odor removal effective
• Common signs it's time: lingering cooking odors, reduced smoke capture, heavily discolored filter media

• Disconnect power and allow the hood and lamps to cool before service
• Remove grease filters to access the charcoal filters; release clips/tabs, swap in the new set
• Seat filters securely; align any arrows or tabs as marked
• Charcoal filters are not washable—replace when saturated

This switch box assembly houses and secures the surface-element switches and their wiring on electric ranges, restoring safe electrical connections and reliable burner control. It's a direct-replacement mounting box used where switch supports or internal wiring need renewal. What it does

• Provides a protected enclosure to hold surface-element switches and route wiring safely.
• Restores stable electrical connections when loose or damaged switch mounts cause intermittent burners.
• Helps stop sparks, arcing, or burnt smells originating from a failing switch mount area.
• Enables proper alignment and installation of surface element controls for consistent heater operation.

• One switch box assembly.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Handle surrounding panels and cooktop glass carefully to avoid damage during removal/installation.
• Verify wire harness and switch compatibility before final assembly; use only OEM-recommended components.

The Halogen Lamp is an OEM part for GE range hoods. It provides bright, illumination for proper visibility above the cooktop.

Halogen lamps experience wear over time from consistent heating and cooling duty cycles. Causes of failure can include normal burnout after hours of use, fracturing of internal filaments, or arcing faults within the lamp. 

Symptoms of a bad halogen lamp include:

• Diminished light output that makes seeing above the range difficult  
• Complete failure to light up when turning the hood on
• Shadows or dark patches visible within the illuminated area
• Premature flickering or instability of the lit area 

This OEM GE halogen lamp is also compatible with Hotpoint, RCA and select Kenmore range hood models.

This is a replacement interior appliance light bulb that restores illumination inside refrigerators and other household appliances for safer, easier loading and food visibility. Designed to match the original part's fit and basic function. What it does:

• Replaces a failed or dim interior light to restore full illumination
• Sits in the appliance light socket and provides consistent lighting when the door is opened
• Commonly used when the light does not turn on, flickers, or is visibly burned out
• Works as the direct replacement specified by the OEM for compatible models

• One replacement light bulb

• Disconnect power or unplug the appliance before replacing the bulb to avoid electric shock
• Allow the old bulb and housing to cool before removing; use a cloth or gloves to avoid burns and oils from skin
• Remove the bulb cover if present, replace the bulb, then reinstall the cover and restore power
• Dispose of the old bulb per local regulations