Parts for Ge UVW9301BL1TS: Range Hood Parts

LED lamp that replaces a failed interior refrigerator light, restoring bright, easy-to-see illumination so you can find items and check contents. Direct-replacement design for a simple bulb swap. What it does:

• Provides interior lighting to replace a burned-out or flickering refrigerator lamp
• Restores visibility on shelves and in crisper compartments
• Uses LED lighting for consistent, long-lasting illumination compared with older bulbs
• Designed to match the original lamp's mounting and connector style for a straightforward replacement

• Always disconnect power to the appliance before replacing the lamp to avoid shock
• Remove the old lamp cover or housing per your appliance manual, then unplug or unclip the old lamp before installing the new unit
• Handle the lamp by its housing; avoid touching exposed LED surfaces or contacts

This rubber ring is a flexible sealing gasket that helps prevent leaks and cushions components where parts join. It restores a tight seal and reduces vibration when a worn or damaged ring causes seepage or noise. What it does:

• Forms a watertight seal at a mating surface to help stop leaks and drips
• Cushions and isolates parts to reduce vibration and rattling
• Helps retain and position connected components for proper alignment
• Commonly replaced if you see cracks, flattening, ripping, or active leaking

• One rubber ring

• Disconnect power and shut off water supply before servicing appliances
• Remove the old ring and clean mating surfaces; inspect for related damage
• Lubricate lightly with water or manufacturer-recommended lubricant to ease installation
• Test operation and check for leaks after reassembly; replace again if new leaks appear

This charcoal filter traps odors in the recirculating vent system, helping your appliance freshen the air when it isn't ducted outdoors. Replace a saturated filter to restore effective odor reduction and keep ventilation working as designed.

• Adsorbs cooking odors from vapors as air passes through the filter
• Intended for non-vented operation of the ventilation system
• Common replacement signs: lingering smells, dark/saturated media, or crumbling when handled
• Works with clean grease filters to help maintain effective odor control

• Disconnect power to the appliance before servicing
• Remove grille or filter cover per your owner's manual; note filter orientation/airflow arrows if present
• Install without bending; ensure it seats fully and the grille/cover is secured
• Charcoal filters are not washable—replace when saturated or as recommended by the manufacturer

This recirculation duct channels exhaust air from the microwave's internal blower through the filters and back into the room when set for non-vented installation, restoring a proper airflow path and helping reduce steam, smoke, and cooking odors.

• Directs exhaust airflow for recirculating microwave installations
• Routes air through filters to help reduce steam, smoke, and cooking odors
• Replace if cracked, warped, or missing to prevent leaks and rattling
• Symptoms include weak or misdirected airflow, persistent odors, or vibration/noise near the vent area

• Disconnect power to the appliance before servicing
• Remove the upper grille/vent cover to access the duct; retain hardware
• Ensure the blower is configured for recirculation and seat the duct fully over the outlet
• Reinstall fasteners and grille; test the fan on each speed to confirm proper airflow

This duct cover bracket is a small metal mounting support that secures the range/hood duct cover to the appliance. It helps keep the vent cover aligned and stable so the external ducting stays properly supported and sealed. What it does:

• Secures the duct cover or vent trim to the appliance chassis to prevent movement
• Keeps the duct cover aligned to reduce gaps where air or odors can escape
• Reduces rattling and vibration caused by a loose duct cover
• Helps maintain a clean, finished appearance around the vent opening

• Basic hand tools are typically all that's needed; follow the appliance service manual for access steps.
• Disconnect power to the appliance before servicing any electrical components.
• Use appropriate fasteners and torque per the manufacturer's instructions; do not overtighten.

This is a self-tapping ST3.5 x 9.5 screw used to secure panels, trim and small appliance components. It replaces missing or damaged screws to restore proper fit and prevent rattling or loose parts. What it does:

• Fastens control panels, brackets, trim pieces and light assemblies
• Replaces stripped, corroded or missing screws that allow parts to shift
• Restores secure mounting and helps eliminate vibration noise
• Small size for low-profile applications where a compact fastener is required

• Use the correct sized Phillips or Pozidriv driver to avoid cam-out
• Start screws straight and drive until snug; avoid overtightening to prevent stripping
• Disconnect power and remove any sharp panels before working to stay safe
• Keep a small parts tray to avoid losing tiny screws during repair