Parts for Frigidaire GL51LPDC: 03 - Recommended Spare Parts

This gauge displays temperature readings for monitoring appliance operating conditions. It provides visual feedback on internal temperatures to help ensure proper operation and food safety. Replace it if the gauge shows incorrect readings, the needle is stuck, or the display is cracked or unreadable.

Grill flavor grid that sits above the burner to distribute heat and protect components. Replace if cracked, warped, rusted, or missing for proper cooking.

If your grill burner won't light or has delayed ignition, this electrode creates the spark needed to ignite gas. Simple DIY fix restores reliable lighting.

This surface burner element replaces a damaged or non-heating cooktop element to restore stovetop heating. It fits compatible Frigidaire electric ranges and provides the actual cooking heat on one cooktop zone. What it does:

• Heats cookware when the range control cycles power to the burner
• Replaces visibly broken, warped, or non-functional surface elements
• Common symptom: burner won't heat or only heats intermittently
• Common symptom: uneven heating or hot spots across the cooking area

• Disconnect power to the range at the breaker before starting any work
• Allow the old element to cool completely and handle terminals carefully
• Slide the element into the cooktop receptacle and secure per your model's socket design

Grill won't ignite or clicking but no flame? This ignition electrode creates the spark to light your burners. Common fix for ignition failures.

If your grill burner won't light or sparks weakly, this electrode spark igniter creates the spark needed for reliable gas ignition. Simple DIY fix.

If your grill won't heat evenly or has weak flames, the burner may need replacement. This part restores proper heat distribution for consistent cooking.

This is a small metal cap that sits on top of a surface burner on a gas range or cooktop. It distributes the flame evenly around the burner for consistent heating. Replace this cap if it is chipped, warped, corroded, or if the burner flame appears uneven or yellow.

Control knob for grill burner adjustment. Installs on the control panel. Replace if your knob is cracked, broken, loose, or missing for proper operation.

Replacement wire for your grill. Installs in the control or ignition system. Order a new one if your existing wire is frayed, damaged, or broken.

The grill igniter wire is the electrical cable that connects the igniter to the power supply on your gas grill. It carries the spark current needed to ignite the burners when you press the ignition button. Replace this wire if your grill won't spark, the igniter clicks but produces no flame, or the wire is visibly cracked or burned.

If your grill has uneven flames or low heat output, the gas pressure regulator may need replacement. Controls gas flow from tank to burners.

Control knob for grill burner adjustment. Mounts on the control panel. Replace if cracked, broken, worn, or missing for proper temperature control.

Burners won't light or spark is weak? This ignitor module restores reliable spark generation to ignite gas burners. Straightforward repair.

Rotisserie fork for grills. Secures food to the rotisserie spit for even cooking. Replace if bent, broken, or missing to restore rotisserie function.

Grill motor not turning? This rotisserie motor replacement restores smooth rotation for even cooking. Moderate DIY repair, typically 30-45 minutes.

This is the left-side end cap that attaches to the end of the oven door or drawer handle. It provides a finished appearance and protects the handle mounting hardware. Replace this end cap if it is cracked, broken, or missing, which can leave the handle feeling loose or expose sharp edges.

This replacement handle end is the small end cap that finishes and secures a refrigerator or freezer door handle for a clean, finished look. It restores a snug fit and hides the handle fastener. What it does:

• Covers and protects the exposed handle fastener or mounting area
• Helps keep the handle snug and prevents wobbling or rotation
• Restores finished appearance to a cracked, chipped, or missing end piece
• Useful when the original end cap is broken, lost, or cosmetically worn

• One handle end (end cap) as pictured

• Usually secures by snapping or sliding onto the handle; may require removing handle or a single screw
• Use basic hand tools; keep screws and brackets for reassembly
• No electrical disconnection required for door-handle end cap replacement

This replacement elbow is a molded connector that routes and secures flexible tubing for proper water or drain flow, restoring sealed connections and preventing leaks. Easy to swap when the original is cracked or worn. What it does

• Connects and redirects flexible tubing to maintain proper water/drain routing.
• Restores a sealed pathway where a cracked or brittle elbow causes leaks.
• Helps stop slow drainage or water pooling caused by a failed connector.
• Provides a secure fit for tubing to prevent disconnection during normal use.

• One replacement elbow as shown.

• Disconnect power and shut off water supply before beginning any repair.
• Remove surrounding panels as needed to access the elbow; retain screws and clips for reassembly.
• Inspect mating tubing and fittings; replace damaged tubing or use approved clamps for a secure seal.

Replacement mounting screw for grill assembly. Secures panels, brackets, or internal components. Order if original screw is stripped, lost, or damaged.

Wire component for grill assembly. Installs internally to connect electrical components. Replace if frayed, damaged, corroded, or disconnected.

This bolt secures the gas valve or manifold assembly to the range body. It ensures a tight, stable connection that is critical for safe gas flow and burner operation. Replace this bolt if it is stripped, corroded, or missing, which can result in a loose valve or manifold and potential gas leaks.

Replacement mounting screw for grills. Secures panels, trim, brackets, and assemblies. Needed when original screw is missing, stripped, or damaged.

Replacement mounting screw for grill assembly. Secures components and panels in place. Order a new screw if original is stripped, missing, or damaged.

This bolt secures the gas valve or manifold assembly to the range body. It ensures a tight, stable connection that is critical for safe gas flow and burner operation. Replace this bolt if it is stripped, corroded, or missing, which can result in a loose valve or manifold and potential gas leaks.

Replacement mounting screw for grill assembly. Secures panels, brackets, or internal components. Order if original screw is stripped, lost, or damaged.

Wire component for grill assembly. Installs internally to connect electrical components. Replace if frayed, damaged, corroded, or disconnected.

Replacement mounting screw for grill assembly. Secures components and panels in place. Order a new screw if original is stripped, missing, or damaged.

Replacement mounting screw for grills. Secures panels, trim, brackets, and assemblies. Needed when original screw is missing, stripped, or damaged.

This is an insulated wire lead that connects the igniter to the infrared broil burner at the bottom of the oven. It carries the electrical signal needed to ignite the burner element. Replace this wire if the infrared burner fails to ignite, if the insulation is cracked or burned, or if you notice intermittent ignition problems.

This is a mounting nut used to secure the bottom door pivot on a range or oven. It holds the hinge pin or pivot bracket in place so the door swings properly and stays aligned. Replace this nut if it is stripped, corroded, or missing, which can cause the oven door to feel loose or hang unevenly.

This is an insulated wire lead that connects the igniter to the infrared broil burner at the bottom of the oven. It carries the electrical signal needed to ignite the burner element. Replace this wire if the infrared burner fails to ignite, if the insulation is cracked or burned, or if you notice intermittent ignition problems.

This is a mounting nut used to secure the bottom door pivot on a range or oven. It holds the hinge pin or pivot bracket in place so the door swings properly and stays aligned. Replace this nut if it is stripped, corroded, or missing, which can cause the oven door to feel loose or hang unevenly.