Parts for Whirlpool EB22DKXFB01: 05 - Refrigerator Door Parts

The Door Gasket is an OEM part for Whirlpool refrigerators. This gasket forms an airtight seal around the refrigerator or freezer door, preventing warm air from entering and cold air from escaping.  

Causes of a bad door gasket can include wear and tear from frequent opening and closing, exposure to temperature fluctuations causing the material to become brittle or warped, and damage from improper cleaning or handling.  

Symptoms of a bad door gasket include:

• The refrigerator door not sealing properly
• Visible cracks, tears, or deformities in the gasket
• Condensation or frost buildup around the door edges
• Increased energy consumption and poor cooling performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The center hinge pin is the pivot for the refrigerator door at the middle hinge. Replacing a worn or broken pin restores smooth door swing and proper alignment so the door closes and seals as designed. What it does:

• Acts as the pivot point for the door on the center hinge
• Helps maintain correct door alignment for consistent gasket contact
• Common symptoms: door sags or drags, uneven gaps, popping open, or squeaking/grinding at the hinge

• 1 center hinge pin

• Disconnect power; remove items from the door and support the door before starting
• Remove the center hinge cover and fasteners, then lift the door off the hinge
• Transfer any spacers/washers in their original order and install the new pin on the hinge bracket
• Reinstall and align the door; tighten fasteners and verify gasket seal

This black handle hole plug fills and covers the exposed mounting hole on appliance handles for a finished, factory appearance and to help keep debris and moisture out. Snap-in design provides a clean cosmetic repair without replacing the whole handle. What it does:

• Covers an unused or damaged handle mounting hole to restore appearance
• Helps prevent dirt, moisture, and pests from entering through the handle opening
• Snaps into the handle recess for a secure, low-profile fit
• Commonly used when a missing or worn plug leaves a visible hole on the handle

• One black handle hole plug

• Repair is typically a simple snap-in replacement; plug aligns with handle recess before seating
• Use a flat plastic tool to remove the old plug to avoid scratching surrounding finish
• Disconnect power and follow appliance manufacturer's safety guidance when accessing handles near electrical components
• Do not force the plug; if fit is tight, handle style to avoid damage

Color: White.

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping