Frigidaire Freezer leaking water: Common Causes & How to Fix

Repair Instructions:

During defrost cycles, melted ice needs to drain out of the refrigerator. If the defrost drain tube gets clogged with debris or freezes over, water can overflow the drain trough. This will cause dripping down to the bottom of the fridge and potentially onto the floor. Inspect the defrost drain and see if it is blocked with ice or particles. Thaw any frozen drain blockage and flush with hot water to open the tube.

How to Replace Frigidaire Freezer Defrost Sensor with Fuse

1. Unplug Frigidaire freezer - Unplug the power cord before starting to avoid electric shock.

2. Locate sensor - The defrost sensor is typically mounted on the evaporator coil inside the Frigidaire freezer.

3. Disconnect wires - Remove the sensor wiring harness connector by gently pulling it off.

4. Unscrew sensor - Unscrew and detach the old sensor from the evaporator coil.

5. Install new sensor - Secure the replacement sensor in the same spot with mounting screws.

6. Connect wires - Plug the wiring harness connector onto the terminals on the new sensor.

7. Check fuse - Confirm the inline fuse on the sensor wiring is intact and not blown.

8. Neatly tuck wires - Make sure all wiring is neatly tucked away and not obstructing any components.

9. Plug in Frigidaire freezer - Plug the power cord back in once the new sensor is installed.

10. Test operation - Allow the Frigidaire freezer to cycle on and off to ensure the sensor is working properly.

Repair Instructions:

The gasket is a rubber seal that runs along the perimeter of the Frigidaire freezer door. Its purpose is to create an airtight seal between the Frigidaire freezer door and the cabinet when the door is closed. Over time, the rubber gasket can become worn, cracked, or torn. Gaps or holes in the gasket allow warm, humid air from the room to seep into the Frigidaire freezer. When this air hits the extremely cold temperatures inside the Frigidaire freezer, it condenses into water droplets. With gaps present, the condensed water can drip out of the Frigidaire freezer and onto the floor, causing a leak.

Repair Instructions:

The Frigidaire freezer has a drain pan at the bottom to collect water after defrosting the evaporator coils. This pan can crack over time, causing water leaks onto the floor. Inspect the plastic drain pan closely for any cracks or damage. If the pan has become warped or broken, it needs replacing. The drain pan is essential to safely capture condensate from the defrost cycles. A damaged pan will lead to water spilling past the broken sides or cracks.

How to Replace Frigidaire Freezer Drain Pan

1. Unplug Frigidaire freezer - Unplug the power cord before starting to avoid electric shock.

2. Remove old pan - Pull the Frigidaire freezer away from the wall and slide the old drain pan out.

3. Clean debris - Use a wet/dry vacuum to remove any water or debris under the Frigidaire freezer.

4. Install new pan - Slide the replacement drain pan into place under the Frigidaire freezer.

5. Level pan - Make sure the new pan is situated flat on the floor beneath the Frigidaire freezer drain tube.

6. Attach drain hose - Securely connect the drain hose to the outlet on the new drain pan.

7. Push Frigidaire freezer back - Carefully push the Frigidaire freezer back into place over the new drain pan.

8. Plug in Frigidaire freezer - Plug the power cord back in once the drain pan is fully installed.

9. Check for leaks - Let the Frigidaire freezer run for 1-2 hours, then check beneath for any leaking.

Repair Instructions:

Frigidaire Freezers have a small drain strap that melts ice in the defrost drain tube. This thin metal strap attaches to the defrost heater and runs into the drain line. When the heater turns on, heat travels through the strap to clear any frozen blockage. If the drain strap falls off or deteriorates, ice can clog the tube causing leaks. Without the strap conducting heat, condensed water from the evaporator will overflow the frosted drain and drip onto the floor. If your Frigidaire freezer lacks this small heating strap, one can be added to prevent freezing.

How to Replace Frigidaire Freezer Drain Strap

1. Unplug Frigidaire freezer - Unplug the power cord to shut off electricity while you work.

2. Remove food and shelves - Take out all food items and removable shelves to clear the work area.

3. Locate drain strap - The drain strap is a thin metal band clipped around the drain tube at the bottom rear of the Frigidaire freezer.

4. Remove old strap - Use pliers to detach the old rusted or broken drain strap from the drain tube.

5. Attach new strap - Clip the new drain strap securely around the drain tube using pliers.

6. Confirm fit - Make sure the new strap fits snugly in place and is not obstructing the drain tube opening.

7. Replace shelves and food - Return the shelves and food to their positions in the Frigidaire freezer.

8. Plug in Frigidaire freezer - Reconnect power once the new drain strap is fully installed.

9. Check for leaks - Let the Frigidaire freezer run for 1-2 hours then check beneath for any water leaks from the drain tube area.

Repair Instructions:

Chest Frigidaire freezers have a drain hole and tube at the bottom to remove water during defrosting or cleaning. The end of this drainage tube has a cap that can come loose or go missing over time. If the cap is not secure, water can drip from the open tube. To prevent leaks, check that the drain tube cap is properly tightened in place. If the cap is lost, replace it with a new one.

How to Replace Frigidaire Freezer Drain Hose Cap

1. Locate drain hose - The drain hose runs from the Frigidaire freezer compartment out to the drain pan.

2. Remove old cap - Gently twist and pull off the old drain cap from the end of the drain hose.

3. Clean hose end - Use a damp cloth to wipe any dirt or debris from the open end of the drain hose.

4. Install new cap - Firmly press the replacement drain cap onto the end of the drain hose until it clicks into place.

5. Confirm fit - Gently pull on the cap to make sure it is securely attached and sealing the drain hose.

6. Position hose - Place the capped end of the drain hose directly over the drain pan outlet.

7. Check for leaks - Power on Frigidaire freezer and let run for 1-2 hours, then check beneath for leaks.

8. Redirect hose - If leaking occurs, reposition the drain hose to drain properly into the drain pan.

Repair Instructions:

The ice maker assembly can malfunction and cause water to overflow or leak from the ice tray. Closely examine the ice maker unit to see if it is the source of any leakage. Look for issues like a cracked tray, overflowing water, or leaks from the ice maker parts. If the assembly is defective and leaking, it will need to be replaced. An ice maker with failed components can spill water rather than properly filling the tray.

How to Replace Frigidaire Freezer Ice Maker Assembly

1. Unplug Frigidaire freezer - Unplug the power cord before starting to avoid electric shock.

2. Turn off water supply - Locate the water supply valve and turn it off.

3. Disconnect wiring - Remove the ice maker wiring harness connector.

4. Remove mounting screws - Unscrew any screws securing the ice maker assembly to the Frigidaire freezer wall.

5. Detach water line - Disconnect the water supply line from the old ice maker.

6. Remove ice maker - Carefully slide out the ice maker assembly and discard it.

7. Install new assembly - Slide the replacement ice maker assembly into the mounting brackets.

8. Reconnect water line - Attach the water supply line to the new ice maker inlet valve.

9. Secure ice maker - Reinstall the mounting screws to secure the ice maker assembly.

10. Reconnect wiring harness - Plug the wiring harness connector back onto the new ice maker.

11. Turn on water and power - Restore water supply and plug Frigidaire freezer back in.

12. Test operation - Allow the ice maker to cycle completely to ensure proper functioning.

Repair Instructions:

A damaged door gasket can cause Frigidaire freezer leaks onto the floor. Gaskets that do not fully seal the door opening allow warm humid air to enter. This creates condensation inside that then drips out through gaps in the faulty gasket. Inspect the gasket closely for tears, cracks, or sections that are twisted or flattened. These defects prevent a tight seal with the Frigidaire freezer body. Replacing a worn or damaged gasket will create a complete seal.

How to Replace Frigidaire Freezer Door Gasket

1. Unplug Frigidaire freezer - Unplug the Frigidaire freezer to avoid electric shock while working on it.

2. Remove old gasket - Use a flathead screwdriver to pry up the old gasket from the door frame. Remove any remaining adhesive residue.

3. Clean surface - Wipe down the Frigidaire freezer door frame thoroughly to remove dirt and debris. Ensure the surface is dry.

4. Apply adhesive - Run a bead of gasket adhesive along the door frame where the new gasket will be installed.

5. Install new gasket - Starting at the corner, press the new gasket firmly into place along the adhesive on the frame.

6. Trim excess - Use scissors to trim off any excess gasket material around the door.

7. Allow adhesive to dry - Let the adhesive cure fully before using the Frigidaire freezer, usually 24-48 hours.

8. Plug in Frigidaire freezer - Plug the Frigidaire freezer back in and make sure the door seals properly when closed.

9. Test seal - Place a piece of paper between the gasket and frame and close the door. The paper should be held firmly in place and difficult to pull out, indicating a good seal.

Repair Instructions:

The Frigidaire freezer drain hose is a component designed to guide defrost water from the evaporator drain pan to the condenser tray where it evaporates. When functioning correctly, it prevents water from collecting inside your Frigidaire freezer or leaking onto the floor. If your Frigidaire freezer is leaking water, a likely cause could be a blockage or damage in this drain hose. Debris, ice build-up, or twists can obstruct the water flow, causing it to overflow and leak. Similarly, if the hose is cracked or has holes, water can seep through these damaged areas.

How to Replace Frigidaire Freezer Drain Hose

1. Unplug Frigidaire freezer - Unplug the power cord before starting to avoid electric shock.

2. Remove food and shelves - Take out all removable shelves and food items to clear the work area.

3. Locate drain tube - The drain tube is in the back bottom of the Frigidaire freezer compartment. Consult manual if unsure.

4. Detach old hose - Loosen any clamps and gently pull off the old drain hose from the drain tube.

5. Attach new hose - Slide one end of the replacement drain hose onto the drain tube outlet.

6. Secure hose - Use zip ties or clamps to securely fasten the new drain hose to the drain tube.

7. Route hose - Run the drain hose through the cabinet and out to the drain pan. Avoid kinks.

8. Plug in Frigidaire freezer - Plug the power cord back in once the new drain hose is fully installed.

9. Check for leaks - Allow the Frigidaire freezer to run for 1-2 hours then check beneath for leaks.

Repair Instructions:

The Frigidaire freezer's automatic defrost cycle melts away frost, producing water that exits through the defrost drain tube. This drain can sometimes get blocked with ice, preventing water from exiting. When the drain freezes over, defrost water will overflow and leak from the Frigidaire freezer's bottom. To open the clogged drain, use a turkey baster and hot water to flush out melting ice inside the tube. If the drain regularly freezes up, installing an electric drain heater can help keep the tube ice-free.