Frigidaire Freezer Hinge Parts

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes squarely against the gasket. Replacing a worn or bent hinge restores alignment and helps maintain a reliable seal and temperature performance. What it does:

• Provides the pivot point and support for the door
• Helps keep the door level for proper gasket contact
• Can help resolve door sagging, rubbing, or binding
• Can help with doors that won't fully close or pop back open
• Addresses play, squeaks, or visible hinge damage

• One hinge assembly

• Disconnect power and support the door before removing hinge fasteners
• Note and transfer any shims/spacers from the old hinge to the new one
• Reuse existing hardware unless the manufacturer specifies otherwise
• After installation, verify door alignment and full gasket contact; adjust as needed

This hinge assembly provides the pivot and support for your freezer door or lid, allowing smooth opening and secure closing. Replacing a worn hinge restores alignment and helps the gasket seal to keep cold air contained.

• Supports and pivots the door/lid during opening and closing
• Maintains alignment so the door/lid closes fully and seals properly
• Can help resolve sagging, binding, scraping noises, or doors not closing all the way
• Replaces a bent, cracked, or seized hinge assembly

• Disconnect power before service; wear gloves.
• Support the door or lid and use a second person to prevent drops or damage.
• Transfer any spacers, bushings, or covers from the old hinge if required.
• Align the hinge, tighten fasteners, and verify smooth operation and gasket seal.

This bottom hinge replaces the lower door pivot on compatible Frigidaire refrigerators to restore proper door alignment and smooth opening. It provides a secure pivot point to help maintain an even close and consistent seal. What it does:

• Supports and pivots the lower edge of the refrigerator door for smooth opening and closing.
• Helps maintain correct door alignment so the gasket seals evenly.
• Common replacement for doors that sag, bind, or do not close evenly.
• Works with the factory mounting hardware and hinge locations on compatible models.

• Disconnect power and remove food and loose items from the door before starting.
• Always support the door while removing or installing the hinge to prevent injury or damage.
• Use appropriate hand tools and avoid overtightening fasteners; check door alignment after installation.
• Refer to your model's service manual or official parts diagram for model-specific steps and torque specs.

This door hinge replaces a worn or damaged refrigerator door pivot to restore proper door alignment and sealing. It helps stop sagging, uneven gaps, and doors that stick or don't close fully. What it does

• Provides a stable pivot point so the refrigerator door opens and closes smoothly.
• Restores proper door alignment to improve the magnetic seal and reduce cold air loss.
• Reduces binding, scraping, and rattling associated with worn hinge points.
• Helps correct a door that droops, drags on the cabinet, or sits unevenly.

• One replacement door hinge.

• Unplug the appliance or disconnect power before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Use basic hand tools; tighten fasteners securely but do not overtighten.
• Refer to OEM instructions for exact hinge location and torque specs.