Maytag Washer A511 Leaking

Fix water leaking from detergent dispenser area or inlet connections with this washer injector valve. Acts as siphon break in water supply system.

This repair kit contains seals and components needed to fix leaks around the washer's tub mounting stem. It prevents water from escaping the wash basket area during operation. Use this kit when you notice water pooling under your washer or leaking from the tub assembly.

Washer leaking during fill? A cracked or clogged injector nozzle is often the culprit. This part directs water into the tub. Simple 20-minute DIY fix.

The Water Inlet Valve is an OEM replacement part for Whirlpool washing machines. It is responsible for controlling the flow of water into the washer tub, ensuring the proper water level and supply for each wash cycle.

Causes of a bad water inlet valve can include sediment buildup or obstructions, electrical malfunctions, or normal wear and tear over time, leading to valve failure or improper operation.

Symptoms of a faulty water inlet valve include:

• The washer not filling with water or filling slowly
• Incorrect or inconsistent water levels during wash cycles
• Water leaks around the valve or inlet area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

Prevents backflow of drain water into fresh water supply. Mounts on top of washer. Replace if cracked, leaking, or damaged to restore proper drainage.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

Connects the washer tub to the drain pump for water drainage. Replace if cracked, leaking, or split. Installs between the tub outlet and pump inlet.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replaces broken or cracked siphon break assembly on your washer. Installs on back panel where drain hose connects. Needed when elbow becomes brittle.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Seals the water path at the injector assembly. Replace if you notice leaks during fill cycles or poor water flow. Confirm fit with your model number.

Water inlet hose for washers and laundry centers. Connects water supply to fill valve. Replace if cracked, leaking, or worn to prevent floor leaks.

Carries wastewater from your washer to the household drain. Replace if cracked, split, or leaking at connections to pump or drain standpipe.

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

Leaking during fill or rinse? This bleach dispenser hose carries bleach from the dispenser to the tub. Quick 15-minute fix stops leaks and restores flow.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

Small metal clip that secures panels, brackets, or tubing in place inside appliances. Replace if bent, fatigued, or missing to restore secure mounting.

Replace this washer gasket seal to stop leaks between components. Worn gaskets cause water leakage and poor performance. Verify fit with your model.

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.