Maytag Washer LAT2600AAE Leaking

This repair kit contains seals and components needed to fix leaks around the washer's tub mounting stem. It prevents water from escaping the wash basket area during operation. Use this kit when you notice water pooling under your washer or leaking from the tub assembly.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Connects the washer tub to the drain pump for water drainage. Replace if cracked, leaking, or split. Installs between the tub outlet and pump inlet.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Water won't shut off or keeps filling when washer is unplugged? Replace the water inlet valve. Easy 30-minute DIY fix for most models. Video available.

The Water Injector is an OEM part for Whirlpool washing machines. This component is responsible for distributing water into the washing machine during the wash cycle, ensuring that clothes are thoroughly saturated and cleaned. It connects to the water supply and directs water into the tub at the appropriate times.

Common causes of a bad water injector include blockages from mineral deposits, wear and tear from frequent use, or damage due to high water pressure. Over time, the injector's effectiveness can diminish, impacting the washing machine's performance.

Symptoms of a bad water injector include:

• Insufficient water entering the washing machine
• Longer fill times or failure to fill at all
• Poor cleaning performance
• Leaks or drips around the injector area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Seals the tub cover to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the tub. Confirm fit with your model number.

Fix water leaking onto the floor or uneven tub filling with this upper water injector. Directs inlet water cleanly into the tub. Easy DIY replacement.

Seals the top of the outer tub to prevent leaks and splashing. Replace if cracked, worn through, or gasket is compressed causing water to escape onto the floor.

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:

• Forms a watertight gasket between two parts in the assembly
• Helps prevent drips or seepage at the connection point
• Restores proper compression when the original seal hardens or deforms
• Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal

• 1 rubber seal

• Disconnect power; for water-bearing assemblies, shut off the water supply
• Access the seal location per your service information and note orientation/depth before removal
• Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
• Ensure the seal is fully seated, reassemble, and test for leaks

This is a rubber gasket that sits inside the water inlet hose connection on your washing machine. It creates a watertight seal between the hose fitting and the water supply valve to prevent leaks. Replace this gasket if you notice water dripping from the hose connections at the back of the washer.

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

Secures the agitator to the drive shaft in top-load washers. Replace this collar if it's cracked, worn, or missing to restore proper agitator alignment.

Bleach leaking onto the floor or not dispensing? A cracked or hardened bleach tube is the likely cause. Simple 5-minute fix with basic tools.