Roper Cooktop Parts

This surface burner valve regulates gas flow to a top burner on your gas range or cooktop. The simmer version enhances low-heat control so the flame adjusts smoothly from a steady simmer to a full boil. What it does:

• Regulates gas to the surface burner as you turn the knob, controlling flame size
• Simmer variant improves stable low-flame performance at lower settings
• Common failure symptoms: burner won't light though the igniter sparks, flame won't adjust or stays at one level
• Knob feels stiff/binds or the stem no longer aligns correctly with settings

• 1 surface burner valve

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the control knob and access the valve/manifold from the control panel or cooktop top
• Note the original valve's orientation for your burner position; transfer mounting hardware as needed and tighten all gas connections securely
• After reassembly, restore gas and check every joint for leaks with an approved leak-detection solution; verify proper flame and adjustment

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

This front leveling leg adjusts the height at the front of your appliance to keep it level and steady. Replacing a worn or missing foot helps eliminate rocking, protect floors, and make fine leveling adjustments simple.

• Threads into the base at the front corner to raise or lower the unit for accurate leveling
• Stabilizes the appliance to minimize rocking and vibration when opening the door or using the cooktop
• Restores proper adjustment when the original foot is stripped, bent, or missing
• Common signs include a wobbling appliance, difficulty leveling, or metal-to-floor contact/scuffing

• Disconnect power; turn off the gas supply
• Protect the floor and use an assistant to carefully slide and tip the appliance
• Start the new leg by hand to avoid cross-threading; finish adjustment with a wrench
• Level front-to-back and side-to-side, then verify stability before restoring service

This mechanical oven thermostat controls cavity temperature. It senses heat with an attached capillary bulb and cycles the heating source to reach and maintain the set temperature for consistent, reliable baking performance.

• Regulates oven temperature by opening/closing internal contacts based on sensor bulb feedback
• Helps restore accurate preheat and steady cooking temperatures
• Common failure symptoms: won't reach set temperature, runs too hot, wide temperature swings, or continuous heating
• Provides direct temperature control on knob-operated models

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Handle the capillary tube carefully—avoid kinks or sharp bends
• Route and clip the sensor bulb exactly as originally installed for proper sensing
• Restore power and verify operation with an oven thermometer

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays properly aligned, helping the door seal engage correctly for safe, reliable operation.

• Supports the weight of the door and controls opening/closing motion
• Helps maintain door alignment so latches/seals engage properly
• Wear or damage can cause sagging, rubbing, squeaking, or difficulty closing
• A misaligned door may prevent the unit from starting or sealing correctly

• Disconnect power and allow the appliance to cool before servicing
• Use gloves and eye protection; doors can be heavy and spring-loaded
• Support the door during removal to prevent damage
• Transfer any hardware from the old hinge to the new one if re-usable

This spark module generates the high-voltage pulses that ignite your gas surface burners. Replacing a failed module restores consistent clicking and lighting so burners ignite quickly and reliably.

• Supplies timed high-voltage pulses to each surface igniter when a burner knob is turned
• Coordinates ignition for four burners
• Common symptoms: no spark on any burner, only some burners sparking, continuous clicking after flame lights, or intermittent/weak spark
• Helps resolve burners that only light with a match

• Disconnect power and shut off gas before servicing
• Access location varies by model
• Label and transfer wires one at a time to the new module; ensure the ground connection is secure
• Reinstall in the original position, route wires away from heat/sharp edges, and test all burners

The broil element is the oven's upper heating element. It delivers intense radiant heat for broiling; replacing a failed element restores proper broil performance and more even browning.

• Provides top, direct radiant heat during the Broil cycle
• Symptoms of failure: no broil heat, uneven broiling, visible blistering/cracks or breaks in the element, sparking or tripping the breaker when Broil is selected
• Helps restore proper searing/finishing from the top of the oven

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; support the element while removing its mounting screws
• Gently pull the element forward and disconnect the two wires; prevent wires from slipping behind the oven liner
• Make firm, clean terminal connections; avoid bending the element, reinstall screws, then test the Broil cycle

This rocker switch controls the exhaust function on the appliance's ventilation system. It restores reliable on/off control of the blower when the original switch becomes worn, sticks, or fails. What it does:

• Provides on/off control for the exhaust/blower circuit
• Replaces a faulty or intermittent rocker that prevents the vent from operating correctly
• Helps address symptoms such as blower won't start, won't shut off, or only works when the switch is jiggled
• Restores proper tactile feel if the old switch is loose, cracked, or stuck

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Access the control panel and note wire positions or take a clear photo
• Transfer wires one at a time to the new switch; ensure terminals are fully seated—do not pull on the wires
• Reassemble panels, restore power, and test exhaust operation

Color: black. Small size. Measures about 2-1/2 inches in diameter.

Kit includes 4 pins.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

Color: White. For black order WPW10202217. For almond order 8522446. If your unable to use your old mounting screws order WP3196164.

This electronic control board is the appliance's main controller. It interprets keypad/sensor inputs and energizes the correct loads so cycles start, run, and finish as selected—restoring reliable operation when the original board fails.

• Coordinates cycle timing and selected options
• Processes signals from user interface controls and sensors
• Switches power to motors, pumps, valves, heaters, or fans via onboard relays
• Typical failure symptoms: no display or response, won't start, cycle won't advance, or recurring error codes

• Disconnect power at the breaker or unplug before servicing
• Use ESD protection and handle the board by its edges
• Document and transfer connectors one-by-one; reuse any mounting hardware as needed
• Follow the service manual for any model-specific programming/calibration or diagnostics after installation

Replace a cracked or shattered front panel with this black outer door glass for your oven/range. It restores the viewing window and finished look while helping the door seal and contain cooking heat as designed.

• Forms the exterior glass panel and viewing window of the oven door
• Helps contain heat and protect the door's insulation
• Replace if glass is cracked, shattered, deeply scratched, or discolored
• Can address a loose or rattling exterior panel after impact

• Disconnect power and allow the oven to cool completely before starting.
• Remove the door per your model's manual and place it on a padded surface.
• Transfer the handle and any trim/brackets from the old panel as required for your model.
• Wear cut-resistant gloves and eye protection; handle glass carefully and avoid overtightening fasteners.

This oven bake burner is designed for Direct Spark Ignition (DSI) ranges. It channels gas from the bake orifice and distributes an even flame under the oven floor for consistent baking performance and reliable light-off during the bake cycle.

• Distributes gas through burner ports to create an even bake flame
• Works with the DSI spark electrode to ignite the bake flame
• Can address uneven or weak flame patterns and delayed ignition in bake

• Disconnect power and shut off gas; allow the oven to cool completely
• Remove the oven bottom and flame spreader to access the burner
• Transfer any reusable mounting hardware or shields from the original burner
• After reassembly, restore gas/power and leak-test any disturbed gas connections per local code

This white oven door handle restores a secure, comfortable grip and a clean, factory look on your range. Replace a damaged or worn handle to bring back confident, everyday door operation.

• Provides a sturdy handhold to open and close the oven door
• Direct replacement for a cracked, loose, or missing handle
• Helps maintain safe, controlled door movement during use
• Refreshes the appliance's appearance with a color-matched white finish
• Common symptoms: handle broken, loose, missing, or discolored

• Disconnect power (and shut off gas, if applicable). Allow the oven to cool completely.
• Access the handle's mounting screws from the inner door; support the outer panel/glass while removing hardware.
• Note the original screw locations and orientation before removal; transfer any trim pieces specific to your model.
• Start screws by hand and do not overtighten to avoid damaging the door skins.