Roper Dryer Parts

Replaces a cracked, dented, or damaged dryer drum bulkhead. This front drum component restores smooth tumbling action when the original is worn or broken.

Secures the air duct to your dryer's blower housing. Replace if loose, cracked, or missing to prevent air leaks and maintain efficient drying. Verify fit.

This gray control knob replaces a worn or broken knob on the console so you can accurately select settings. It fits onto the timer/selector shaft and restores a secure grip with smooth, positive engagement. What it does:

• Attaches to the control/timer shaft on the front panel
• Lets you turn and select cycles or options
• Restores a snug fit when the original knob is cracked or stripped
• Common symptoms: knob spins freely, falls off, won't turn settings, or is missing

• 1 gray control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; retain any insert/clip used by your model
• Align the new knob with the shaft and press firmly until fully seated
• Test all settings for proper engagement

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

Note: END CAP KIT CONTAINS (1) RH. & (1) LH. CAP

Replace your dryer's cracked, dented, rusted, or damaged door assembly. Restores proper closure and appearance. Direct-fit replacement installs easily.

This replacement box/housing restores the appliance's original enclosure where internal components mount, protecting wiring and parts from damage. It helps maintain safe operation and prevents loose components from shifting. What it does:

• Provides a protective enclosure for internal components and wiring
• Keeps parts properly positioned to prevent rubbing or disconnection
• Helps reduce vibration-related noise caused by loose components
• Restores a secure mounting point for associated hardware

• Disconnect power to the appliance before beginning any work
• Remove panels as needed to access the original box; keep fasteners for reuse
• Inspect surrounding wiring and components while installing the new box

This bake heating element replaces the oven's primary heating element to restore consistent bake performance and even oven temperatures. Designed to heat quickly and quietly for reliable cooking results. What it does:

• Heats the oven cavity for baking and general cooking cycles
• Replaces a cracked, visibly burned, or non-heating element
• Helps restore oven temperature recovery and cooking consistency
• Stops symptoms like no heat, weak heat, or uneven browning

• Disconnect power at the breaker before servicing the oven
• Remove the oven racks and access the element from inside the oven
• Secure mounting screws and electrical connectors firmly; avoid overtightening

0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.

This bulkhead is the structural panel that supports and seals the washer tub and provides mounting points for related components. It restores proper alignment and containment so the washer can hold and drain water correctly. What it does:

• Provides a secure mounting surface for the tub, seals, and associated fittings
• Helps route and contain water inside the washer cabinet to prevent leaks
• Maintains correct alignment for the tub and connected components
• Commonly replaced when leaks, cracks, or warped mounting surfaces cause water loss or misalignment

• One bulkhead panel

• Turn off power and water supply before beginning any repair
• Handle gently to avoid damaging mating surfaces or embedded seals
• Verify matching orientation and fastener locations to the original part
• If seals or gaskets are attached separately on your model, replace them as needed

Extends your dryer's exhaust duct to reach distant venting points. Replace if your current extension is crushed, kinked, or too short for proper routing.

Protective cover that shields the manifold assembly from dust and debris. Replace if cracked, broken, or missing to restore a secure, finished look.

Wire harness assembly that routes power and control signals between dryer components. Replace if wires are damaged, worn, broken, or connections are loose.

Replace your dryer's worn, cracked, or missing push-to-start knob. This push-on style control knob restores the start button for easy operation.

Flat drying rack installs inside dryer drum to hold delicate items like sweaters and shoes. Prevents tumbling for safe, shape-preserving drying.

Rubber bumper. Color: Grey.