Roper Microwave Parts

8-32 thread screw fastens panels and components inside ranges, ovens, and cooktops. Replace stripped, missing, or damaged screws to secure covers properly.

Replace a cracked, broken, or missing microwave door handle. Restores secure grip and smooth operation. Direct fit for factory-fresh look and feel.

Outer door panel replaces cracked, broken, or missing microwave door frame. Restores clean appearance and protects internal components on select models.

This piston assembly restores the moving piston used in the appliance's fluid/valve system to help recover proper dispensing and motion. It replaces a worn or damaged piston so the affected function can operate as intended. What it does:

• Replaces the piston that moves inside a valve or dispenser to control fluid or airflow
• Restores proper actuation and sealing that can prevent drips or improper dispensing
• Commonly installed when symptoms include poor dispensing, leaks near the valve area, sticking motion, or unusual noises during operation
• Works as a direct-fit replacement where this OEM piston assembly is specified

• One piston assembly as shown

• Disconnect power (and water supply or gas, if applicable) before starting any repair
• Follow the appliance service manual and use appropriate tools; keep small fasteners and seals organized
• Inspect sealing surfaces and O-rings; replace damaged seals to ensure a leak-free install
• Test the appliance after installation to confirm correct operation

This is a replacement screw used to secure appliance parts and panels. It restores proper fastening where the original screw is missing, stripped, or corroded. What it does:

• Secures panels, brackets, or components in place to maintain appliance alignment
• Replaces lost, damaged, or rusted fasteners for a reliable hold
• Helps prevent rattling or movement caused by a missing screw
• Works wherever the OEM screw specification and fit match

• One screw

• Use the matching screwdriver or driver bit; avoid overtightening to prevent stripping
• Disconnect power and follow appliance safety precautions before servicing

This propeller is the small impeller that mounts to the dishwasher circulation pump to move wash water through the spray arms for effective cleaning. Replacing a worn or damaged propeller restores proper water flow and wash performance. What it does:

• Spins on the pump shaft to circulate wash water through the spray arms
• Restores normal water flow when a cracked or stripped propeller reduces circulation
• Helps resolve symptoms such as poor cleaning, weak spray, or inconsistent water movement
• Works with the pump motor; does not include the motor or pump housing

• Disconnect power and water supply before beginning any repair
• Access the pump assembly from the dishwasher base or cabinet front per your model service instructions
• Inspect the pump shaft and seal for wear; replace damaged components to prevent repeat failure
• Reassemble carefully and test operation

This replacement power cord supplies electricity to the appliance so it can run safely and reliably. It replaces a worn, frayed or damaged cord to restore steady power and reduce risk of electrical problems. What it does:

• Delivers mains power from the outlet to the appliance's internal wiring
• Replaces cords with visible damage, exposed wires, or broken plug ends
• Stops intermittent power or complete loss of power caused by a damaged cord
• Helps prevent arcing and poor connections when original cord has failed

• Always disconnect power at the wall or breaker before inspecting or replacing the cord
• Secure the cord strain relief and ensure wire connections are tight and correctly routed

Duct cover guard for microwaves. Installs over ductwork opening to protect and conceal venting components. Replace if cracked, broken, or missing.

Microwave door seal creates an airtight barrier for efficient heating. Replace if worn, cracked, or causing steam leaks. Verify fit with your model number.

Front mounting bracket for microwave installation. Secures microwave to cabinet or wall. Replace if bent, cracked, or missing for proper support.

This replacement base is the lower cabinet support that secures the appliance frame and helps keep the unit stable during operation. Restores proper alignment and support for the cabinet and internal components. What it does:

• Supports the appliance cabinet and keeps the cabinet aligned with the chassis
• Helps reduce cabinet sag, excessive movement, and rubbing against the floor
• Can resolve vibration, rocking, or uneven operation caused by a damaged base
• Provides the mounting surface for other lower-frame components

• Disconnect power (and gas if applicable) before starting any repair
• Use basic hand tools to remove and reinstall mounting fasteners; keep hardware organized
• If any clips, gaskets, or fasteners are damaged, replace them to ensure a secure fit