Roper Wall Oven Parts

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

This replacement power cord restores the appliance's main AC connection so it can receive power safely. Use this cord when the original cable is frayed, cut, melted, or otherwise damaged to prevent intermittent power or electrical hazards. What it does:

• Replaces the appliance's factory power cable to restore reliable electrical connection.
• Transmits mains power from the outlet to the appliance's internal wiring and controls.
• Addresses symptoms such as no power, intermittent power loss, visible cord damage, or burn/melt marks at the cord or plug.
• Helps prevent electrical arcing or shorting caused by damaged insulation or exposed conductors.

• Disconnect the appliance from power at the breaker or unplug before starting any work.
• Verify the cord matches the appliance's connector and routing; do not modify cord ends or splices.
• Secure all strain reliefs and terminal connections per the appliance's service instructions.

This burner ignitor switch controls spark delivery to a cooktop burner so the burner lights when the knob is turned. It replaces a worn or failed switch to restore ignition responsiveness and consistent sparking. What it does:

• Routes spark current to the surface burner ignitor when the control knob is turned
• Stops spark delivery when the control knob is released or turned off
• Commonly used when a burner fails to spark or sparks intermittently
• Works with the cooktop's ignition system to enable safe, reliable lighting

• One burner ignitor switch

• Disconnect power (and gas if applicable) before servicing to avoid shock or injury
• Access may require removing the cooktop or control panel
• Verify wiring and switch operation with a multimeter before replacement

Color: White. Size: 13 oz. Spray paint primer. can.

This cooktop grate kit replaces damaged or worn grates to restore stable, even support for pots and pans on a gas range. It helps maintain proper burner performance and keeps cookware level during cooking. What it does:

• Provides a sturdy surface for cookware so pots and pans sit flat and stable over burners
• Protects the cooktop surface from spills and direct flame contact
• Restores proper cookware alignment if existing grates are warped, chipped, or heavily worn
• Helps reduce wobble and improves cooking consistency when grates are compromised

• Turn burners off and allow the cooktop to cool completely before removing or installing grates
• Lift old grates straight up; install new grate pieces so they sit flush and stable over each burner
• No special tools typically required, but follow your range manual for any model-specific steps

This replacement screw secures panels and small components on your appliance to restore proper fit and help prevent rattling or loose parts. Use it wherever the original fastener has been lost or damaged. What it does:

• Secures trim, panels, or mounting brackets to keep components aligned
• Prevents vibration and rattling caused by loose fasteners
• Replaces missing or stripped screws that compromise panel fit
• Restores reliable fastening so doors and controls sit correctly

• Disconnect power before accessing internal panels or components
• Use the correct driver to avoid stripping the screw head
• Thread carefully and do not overtighten to prevent damage
• Keep small parts away from children and pets

This flat-head 10-32 zinc screw secures panels and components on compatible appliances, providing a corrosion-resistant fastener for reliable mechanical fastening. Use when replacing stripped or missing panel screws to restore proper fit. What it does:

• Fastens control panels, trim, or small appliance components with a 10-32 thread size
• Zinc plating helps resist rust and wear in typical household environments
• Replaces missing, damaged, or stripped flat-head screws that prevent panels from seating correctly
• Fits applications that require a countersunk/flush head for a clean finish

• Use the correct 10-32 driver bit and moderate torque to avoid stripping the head or threads
• Ensure the screw is the correct length and head style for your application before tightening
• Disconnect power to the appliance and follow OEM safety instructions before servicing

This is a package of twelve replacement nuts used to secure appliance panels and components. These genuine-style nuts restore fastener retention to reduce looseness and rattling and help keep parts aligned during operation. What it does:

• Secures panels, brackets, and fasteners to maintain proper component alignment
• Prevents vibration-related loosening that can cause noise or intermittent contact
• Replaces missing or damaged nuts that can allow parts to shift or fall off
• Used wherever the matching nut size and thread are required by the appliance

• Disconnect power (and gas, if applicable) before servicing the appliance.
• Verify the nut size and thread match the stud or bolt before installation.
• Hand-start threads, then tighten with the appropriate driver or wrench; avoid overtightening.

This inset control knob replaces a worn or broken stove/oven control knob to restore secure, easy control of temperature and function settings. It matches OEM fit for direct replacement on compatible GE ranges and cooktops. What it does:

• Replaces a damaged or stripped control knob so settings turn and stay in place
• Provides a positive grip for precise temperature and function selection
• Restores correct fit on the control shaft to prevent slipping or wobble
• Helps resolve symptoms like a loose, cracked, or hard-to-turn knob

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Pull off the old knob straight from the control shaft; align splines and press the new knob onto the shaft until fully seated
• Do not force the knob; if it won't seat, verify shaft type and orientation to avoid damage

The Range Surface Element Wire Harness is an OEM part for Whirlpool ranges and cooktops. This harness routes power between the switches and surface heating elements.

Causes include continuous exposure to cooking heat, mechanical stress from opening/closing element covers, and standard wear over time.

Symptoms of a malfunctioning wire harness include:

• Inaccurate or inconsistent element temperature readings
• Elements failing to turn on or heating unevenly
• Error codes related to element malfunctions

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 8-32 thread screw fastens panels and components in compatible appliances, restoring secure mounting and stopping rattles or loose parts. Use it to replace stripped or missing fasteners and maintain proper alignment of covers and assemblies. What it does

• Secures panels, control boards, brackets, and accessory parts to the appliance chassis
• Restores proper fastening when original screws are missing, damaged, or stripped
• Helps eliminate vibration noise and loose-fit symptoms
• Matches common 8-32 appliance thread standards for a direct replacement

• One 8-32 thread screw

• Disconnect power to the appliance before beginning work to avoid shock or injury
• Use the correct-size Phillips or hex driver to prevent cam-out and head damage
• Install by hand first to engage threads, then tighten snugly—do not overtighten to avoid stripping