Dryer Waste Small Engine Flywheel Key Parts

I WENT ON-LINE & FOUND APPLIANCE STORE,THEY HAD MY PARTS, I ORDERED, THEY WERE SHIPPED IMMEDIATELY,WITHIN UNDER TWO DAYS.THIS WAS EXACTLY WHAT THEY SAID THEY WOULD DO.ALSO THE REPAIR VIDEO SHOWED ME HOW TO RUN THE BELT ON THE TENSIONER,I WAS AMAZED AT HOW SIMPLE & QUICK EVERYTHING WENT BACK TOGETHER.THANKS APPLIANCE STORE FOR BEING THEIR TO HELP ME GET MY GRANDSON"S DRYER BACK WORKING,I GIVE YOUR SITE A < A+ >. Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

• Door won't close

There is a video on youtube that talks about how to disassemble the electronic component out of the control board so I really won't go into that part of it. This disassembly of the control board will need to take place before you can even get started taking the gray piece out of the console to replace it. Be careful not break off the little tips behind the control knob, don't force it, it does come apart easily and there is an easy way to do it, that is also on youtube. This is where the... Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

Use the videos on this website here and you can repair most brands. Many are duplicate in design. 1. Unplug the machine. 2. Move it away from a confined area to get more room. 3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet. 4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you... Read more

I went to the local Home Depot and Lowes, but they did not have the parts because they do not carry parts for the items they actually sell to people. Jumped on the phone and did a quick search for parts and came across appliancepartspros.com. I put in the make and model of my dryer and all the parts for the dryer where listed. I ordered the items on a Wednesday night. I opted for the two day shipping. I thought the items would be at my house by Friday but they did not arrive until Monday. I... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Use the videos on this website here and you can repair most brands. Many are duplicate in design. 1. Unplug the machine. 2. Move it away from a confined area to get more room. 3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet. 4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you... Read more

• Door won't close
• Won't start

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

• Will not tumble
• Noisy

I've had this dryer apart a few times over the years, always got my parts here. Squeaks and igniter if memory serves. I ordered the two drum rollers that have a bearing in the center..they sit on metal shafts and freeroll. I ordered two..only one was bad but I needed the dryer up in one day, no time to disassemble and decide what to order then wait for parts. Tip: if you order the rollers, there are little washers (nylon?) between the roller and the c clips..don't lose them..they are hard to... Read more

Replaced the drum rollers Read more

Replaced Read more

The Dryer is 10 years old GE Front Load DPVH890JEMG. The drum would intermittently not rotate at the beginning of a cycle and occasionally would rotate but then start and stop throughout the cycle. I did not check error codes, but the windings on the motor were black. So it seemed reasonable that the motor was overheating and sending a signal to the control board to stop. There is one screw under the knob and 9 screws on the front to get inside. I decided to replace the bearings, capacitor,... Read more

We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more

Our dryer was making such a load noise that we deemed it unusable. We weren't sure if something would burn up if it continued like it was. So I checked a few articles on the internet and everything pointed to most likely the drum belt. Ours looked a little worn but not really that bad so I got the part. I then followed the repair video that AppliancePros had posted for my model (which was great) and installed the belt. Still squeaking. So I went on to #2 on the list of possible problems, the... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more