Refrigerator Insert Control Panel Parts

This small white plastic plug covers an unused hinge bearing hole on the refrigerator door, typically left open when the door is configured to swing in one direction. It provides a clean, finished look and prevents moisture or debris from entering the hole. Replace this plug if it is missing, cracked, or yellowed, restoring the door's appearance.

The Mullion is an OEM part for Frigidaire refrigerators. It is situated between the freezer and refrigerator doors to separate the two compartments. The mullion provides structure, sealing the doors against air and temperature leakage.

Causes of a bad mullion can include wear and tear over time, damage from frequent door opening and closing, or impact damage.

Symptoms of a bad mullion include:

• Air and temperature leakage between compartments
• Difficulty closing one or both doors securely
• Gaps or cracks seen around the mullion frame
• Scratches, dents or other physical damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Fridge not cooling or excessive frost buildup? A faulty defrost timer may be cycling incorrectly. Straightforward DIY replacement restores automatic defrost.

Fix freezer icing and warm fridge temps by replacing a faulty defrost timer. Typical DIY repair takes 15-30 minutes with basic tools and a multimeter.

This thermostat is a temperature-sensitive safety switch that monitors heat and opens or closes the circuit at a set point. Replacing a failed thermostat restores reliable temperature protection and corrects issues caused by tripping or stuck contacts.

• Monitors component/cavity temperature and trips at a preset limit
• Opens (or closes) the electrical circuit to prevent overheating or activate cooling functions
• Common symptoms: no heat or intermittent heating, unit won't start or shuts off during use, cooling/vent fan runs constantly or never turns on
• Useful diagnostic clue: faulty thermostats may test open or stuck closed at room temperature

• Disconnect power at the breaker before servicing; if used in a microwave, be aware the high-voltage capacitor can retain a dangerous charge
• Note wire locations; transfer one lead at a time and secure the thermostat in the original mounting position for proper sensing
• Ensure clean metal-to-metal contact with the mounting surface; do not overtighten screws
• After installation, restore power and verify normal operation

Clear plastic dairy door cover for refrigerator compartments. Replaces cracked, broken, or missing covers. Keeps butter and cheese organized.

The Dispenser Control Board is an OEM replacement part for Frigidaire refrigerators. This component manages the operation of the ice and water dispenser, controlling functions like dispensing ice, water, and the corresponding display settings. It ensures that the dispenser operates correctly by communicating with other components, such as the ice maker and water valve.

Causes of a bad dispenser control board can include electrical malfunctions, power surges, or wear from regular use, which can affect the board’s ability to send signals to the dispenser components.

Symptoms of a bad dispenser control board include:

• Ice or water not dispensing properly
• Display or indicator lights not functioning
• Dispenser buttons unresponsive
• Intermittent or complete dispenser failure

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Plastic insert that seats inside the refrigerator air damper cover to guide airflow from freezer to fresh food. Replace when cracked, broken, or missing.

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

Fix blank displays, inaccurate temperature readings, or unresponsive controls. This control board regulates cooling cycles and monitors sensors. Moderate DIY.

Fixes refrigerator temperature issues and cooling failures. Replaces faulty control board causing warm compartments or compressor problems. 45-minute DIY fix.

Fixes refrigerator not cooling, dispenser won't stop running, or unresponsive controls. Main control board regulates temperature and defrost cycles.

This thermostat is a temperature safety device that opens the circuit if temperatures climb beyond the safe threshold. Replacing a failed thermostat helps protect the appliance from overheating and restores normal heating performance.

• Monitors internal temperature and cuts power if it overheats
• Helps prevent damage to components from excessive heat
• Common failure signs include no heat, intermittent heat, or the unit shutting off on high heat
• Shows continuity when cool and open when tripped

• Disconnect power before service; verify no voltage is present
• Access location varies by model; note wire positions and transfer one at a time
• Mount firmly against the intended surface for proper sensing
• After replacement, verify airflow/venting and clear lint/debris to avoid repeat trips

Fix a fridge that won't stay cold or runs constantly. This mechanical temperature control thermostat regulates cooling cycles. DIY-friendly repair.

Fix a refrigerator with no power or a compressor that won't run by replacing the main power control board. DIY-friendly repair takes about 30 minutes.

Fix a refrigerator that stopped cooling overnight with this inverter control board. Moderately easy DIY repair with just two harness connectors to attach.