265D1830g003 Parts

Original Whirlpool light bulb, 40 watt.

Symptoms of needing to replace the light bulb include:

• Dimming or flickering light
• Complete lack of illumination inside the appliance
• Visible signs of damage or burnout on the bulb itself

Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.

Traps grease and particles from cooking to maintain efficient ventilation. Replace every 6-12 months depending on usage. Confirm fit with your model number.

Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.

Replace worn, cracked, or faded burner control knobs on your cooktop. Restores clear temperature markings and secure grip for adjusting heat settings.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Fix a downdraft fan that stops working, vibrates excessively, or cycles on and off. This blower motor replacement takes 1-2 hours to install.

This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.

• Fastens exterior panels, trim pieces, or internal brackets to the appliance chassis
• Replaces lost, damaged, or stripped hardware
• Helps prevent vibration, rattling, and gaps between parts
• Common signs you need this screw: missing hardware, loose or misaligned panel/trim, stripped head or threads

• Disconnect power before servicing; also shut off the gas supply
• Use the correct driver; start the screw by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping or cracking adjacent parts
• Repair or replace the mounting point before installing

By Jenn Air/Maytag. 8 inch adapter ring. Fits some Jenn Air models. For the 6 inch order WPY707454.

This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:

• Moves air across the heater, through the drum, and out the vent to remove moisture
• Helps maintain proper airflow and temperature inside the dryer
• Common failure symptoms: reduced or no airflow at the exterior vent, longer dry times, unusual scraping/thumping or vibration from the blower area, or overheating/shutoff
• Cracked fins or a stripped hub can cause the wheel to slip on the motor shaft

• 1 blower wheel

• Disconnect power and turn off gas supply before servicing
• Access the blower housing per your model's service instructions; remove the retaining hardware and replace the wheel in the same orientation
• Clean lint from the blower housing and vent path; inspect the motor shaft and blower seal for wear
• Reassemble and verify the wheel spins freely without rubbing; check airflow at the exterior vent

6-inch adapter ring for cooktop drip pans. Replaces cracked, rusted, or worn rings on drop-in electric cooktops. Restores clean appearance.

Screw: 8-16 x 3/8 inch.

Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.

Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.

Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.

This is a genuine MTD fuel cap replacement made for use on select snowblowers. It features a molded gasket for secure sealing and less risk of losing parts. The fuel cap is responsible for securing the fuel in the fuel tank during operation so that it doesn't spill out. There is an air hole in the cap to prevent pressurization of the fuel, ensuring safe operation at all times. This cap is made of plastic and it can become cracked or stripped with regular use. If it is damaged, the fuel will not be secure and the machine will not be safe to use. That will require an immediate replacement. This OEM fuel cap is made to exact standards by MTD and is compatible with several models of snow blowers and snow throwers. It is also capable of fitting select models from Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. It features an easy plastic grip and a seal to prevent spillage. It can be installed with no tools and is sold as an individual unit. It is easy to screw the new cap into place, but be sure to thread the screw properly to prevent accidental stripping or misthreading that can cause the cap to get stuck.

Seals the fuel bowl to prevent leaks and keep dirt out of your fuel system. Replace when cracked or leaking. Confirm fit with your model number.