665147 Parts

This small retainer secures the flexible tine-row "comb" on the dishwasher rack. Replacing a cracked or missing clip keeps fold-down tines aligned and stable so dishes load properly and rack parts stay in place.

• Holds the flexrow comb firmly to the dishrack to support adjustable/fold-down tines
• Helps prevent the comb strip from loosening or popping off the rack
• Common symptoms: flexrow won't stay attached, tines collapse or misalign, broken or missing clip
• Restores original rack function and stability

• Disconnect power to the dishwasher for safety
• Pull the rack out and locate the flexrow comb and its retainer
• Release the old retainer's locking tabs (a small flat-blade screwdriver can help), then remove it
• Align and snap the new retainer into place; the tines move and lock as intended

Note: Left Hand side with release lever.

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Color: light grey. It measures about 2-1/2 inches high by 2 inches deep.

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

May also be called a key. Color: Red.

12 Ft in length

The Wire Harness is an OEM component compatible with Whirlpool built-in dishwashers. Located internally throughout the dishwasher chassis, it provides electrical connectivity between control systems, motors, valves and other modules.

Causes of wire harness failure are often insulation breakdown from continuous flexing during operation or moisture damage. Physical snags can also abrade protective sheathing. 

Symptoms of a bad wire harness include:

• Intermittent functionality of components powered by harness    
• Error codes or failure detection of connected modules
• Water leaks around entry/exit points due to split sheathing
• Fraying, broken or disconnected wires within the bundle

This authentic Whirlpool replacement is compatible with select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore models. 

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

This rotary start-run switch controls power to the appliance motor. Turning the knob engages the motor circuit to start and keep it running, restoring reliable on/off operation when the original switch wears out.

• Controls motor power using a rotary action
• Replaces a worn or intermittent switch that causes no start, stops, or inconsistent operation
• Helps resolve issues like fan/blower not turning on, cutting out, or only running in certain positions
• Designed for correct fit and dependable switching in compatible units

• Disconnect power before servicing to prevent electrical shock
• Note wire locations or take photos before removing the old switch
• Transfer wires to the same terminals on the new switch; secure connections firmly
• Test operation before reassembling any panels or knobs

Includes two screws, two clamps, and undercounter mounting brackets.

The Nut is an OEM replacement part for Whirlpool dishwashers. It is a small part that secures the kickplate, or the lower front panel of the dishwasher, in place. This nut ensures a secure and tight fit for the kickplate, preventing it from becoming loose or falling off during dishwasher operation. 

A bad nut can occur due to wear and tear, accidental damage, or misplacement. If you notice symptoms such as a loose or wobbly kickplate, or if the kickplate has completely detached from the dishwasher, it may indicate a faulty or missing kickplate nut.

Symptoms of a bad nut include:

• Loose or wobbly kickplate
• Kickplate completely detached from the dishwasher

Restore your dishwasher by replacing the faulty or missing kickplate nut with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This normally closed pushbutton switch controls an on/off circuit in the appliance. Replacing a worn switch restores reliable light shutoff and interlock response so the unit behaves correctly when the button or door/plunger is pressed.

• NC operation: circuit is closed at rest and opens when the button is pressed
• Commonly used for door/light or interlock "off" functions in compatible assemblies
• Symptoms can include: light stays on with door closed, light won't turn on, unit won't start because door isn't detected, or intermittent operation
• Helps ensure consistent, repeatable switch actuation

• Disconnect power before servicing
• Note/photograph wire locations; move wires to the same terminals on the new switch
• Mount securely and align the actuator with the button or door plunger
• Restore power and test for proper operation before reassembly