Gfd65gspnsn Parts

The Lint Filter is an OEM component for GE clothes dryers. Located inside the dryer cabinet behind the door, this filter screens lint and other debris from the air stream before it is recirculated during the drying cycle. Consistent lint filtering is essential for safety and performance.

Causes of a lint filter becoming clogged or damaged could be a failure to clean after each use, dryer vent duct restrictions slowing airflow, or material deterioration from heat and extended use.  

Symptoms of a bad lint filter include:

• Slow or inefficient drying times  
• Excessive warmth of the cabinet, burner housing or vent ductwork
• Burned lint smell or visible lint buildup in the duct or venting area
• Tripped thermal fuses or blown heating elements due to restricted airflow

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The LP Conversion Kit is an OEM part for GE dryers. This kit allows for the conversion of a natural gas dryer to operate on liquid propane (LP) gas. It includes all necessary components to ensure a safe and efficient conversion process, including a new orifice, regulator spring, and installation instructions.

Causes of needing a conversion kit can include moving to an area where only LP gas is available or preferring the use of LP gas over natural gas. Additionally, some users may find LP gas more economical or suitable for their specific needs and appliances.

Symptoms indicating a conversion is needed include:

• Moving to a location without natural gas service
• Preferring the use of LP gas for cost or availability reasons
• Acquiring a natural gas dryer when LP gas is the available fuel source

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Roller Assembly Wheel is an OEM part for GE dryers. It supports the drum and allows it to rotate smoothly during drying cycles, ensuring efficient and quiet operation. The assembly includes the roller, roller axle shaft, and two retaining clips. The roller is threaded on one side and hexagon-shaped on the other, with a tri-ring included for secure installation.

You should replace this roller assembly wheel if it becomes worn or damaged. Common causes of a bad roller assembly wheel include wear and tear from regular use, accumulation of lint and debris, or damage due to overloading the dryer.

Symptoms of a bad roller assembly wheel include:

• Thumping or squeaking noises during operation
• The drum not rotating properly or getting stuck
• Uneven drying of clothes
• Excessive vibration or movement of the dryer

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: Dark Slate

The Door Strike is an OEM part for GE dryers. Positioned on the dryer frame, it securely latches the door closed during cycles. Its magnets align perfectly with the door when shut to create an air-tight barrier, enhancing energy efficiency.

Causes of failure can be normal wear, misalignment stress, or accidental damage. Over time, strikes lose effectiveness at preventing air/moisture exchange.

Symptoms of a bad door strike include:

• Excess warm air entering the dryer chamber
• The door not fully closing or latching tight
• Clothing not drying completely within expected cycles
• Buildup of lint around the door seal area

This GE part is also compatible with some Hotpoint, RCA, and Kenmore models.
 

The Door Protect Cover is an OEM part for GE dryers. It acts as the outer door glass safeguarding the dryer door opening from external debris and impacts.

Causes of a bad door protection cover can include cracks or breaks from repeated door slamming over time. Warping from heat exposure inside the dryer cabinet is also possible.

Symptoms of a bad door protection cover include:

• Difficulty sustaining a secure door seal  
• Strange noises or vibrations emanating from the door area
• The door failing to latch fully in place during cycles
• Obstructed drum rotation from a misaligned protect cover

This genuine GE replacement part is compatible with Hotpoint, RCA and select Kenmore dryers.

The Drive Belt is an OEM replacement part for GE dryers. It is responsible for transferring rotational power from the dryer's motor to the drum, allowing it to spin during the drying cycle.

Symptoms of a faulty dryer drive belt include:

• Drum not spinning
• Unusual noises coming from the dryer
• Inability to start the drying cycle

A bad dryer drive belt can be caused by wear and tear over time or damage due to excessive tension, improper installation, or overloading the dryer. If you notice that the drum is not spinning or if you hear unusual noises during operation, it may be time to replace the old or damaged drive belt with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This door switch senses when the dryer door is closed so the cycle can start, and cuts power when the door opens. Replacing a faulty switch restores safe operation and consistent start/stop behavior tied to the door. What it does:

• Detects door open/closed position to enable or interrupt the motor and heater
• Stops drum rotation and heating when the door is opened
• On many models, also controls the interior drum light
• Common symptoms: dryer won't start, drum doesn't stop when door opens, interior light stays on/off incorrectly, intermittent starting

• 1 door switch

• Disconnect power before servicing
• Access the switch behind the door opening (remove the top or front panel as required by the model)
• Note wire positions; transfer connectors to the new switch and secure it in the bracket
• Reassemble and test that the dryer starts only with the door closed and stops when opened

The Thermostat is an OEM part for GE dryers. It monitors air temperatures inside the dryer drum during cycles to ensure they remain within a designated safe range. As a safety component, the thermostat automatically cuts power if temperatures get too high, protecting dryer components from damage.

Causes of a bad thermostat can include normal wear and tear over time from repeated heat cycles. Mineral buildup interference or electrical faults may also cause premature malfunction.

Symptoms of a faulty thermostat include:  

• Inability to properly heat or maintain consistent air temperatures
• Unexpected fluctuations outside of set temperature points   
• Issues fully completing designated drying cycles  
• Potential overheating errors or safety trips

This genuine OEM GE replacement thermostat restores accurate temperature monitoring and controls. Compatible with some Hotpoint, RCA, and Kenmore models as well, it improves performance reliability and safety once installed.

A replacement baffle screw and flat washer used to secure the baffle or trim piece in ovens and ranges. Restores proper attachment to reduce vibration and keep the baffle aligned for normal operation. What it does

• Secures the baffle or trim to the oven/range body and prevents movement or rattling.
• Replaces missing, stripped, or corroded mounting hardware that can cause loose or misaligned baffles.
• Helps maintain a tight fit so trim and baffle sit flush with surrounding panels.
• Small, direct-replacement fastener for original baffle mounting points.

• Disconnect power and allow the appliance to cool before accessing internal panels.
• Use the matching size screwdriver; start threads by hand to avoid cross-threading.
• Tighten until snug — avoid over-tightening, which can strip threads or deform the washer.
• Repair or replace the mounting bracket before installing this hardware.

This outlet thermistor monitors exhaust air temperature in the dryer's outlet duct and reports it to the control. Replacing a faulty sensor helps restore accurate heat regulation, preventing over- or under-drying for consistent drying performance. What it does:

• Measures outlet/exhaust air temperature and sends a resistance signal to the control board
• Helps the control cycle the heater or burner on/off to maintain proper drying temps
• Failure symptoms can include long dry times, no heat, overheating/shutting off, or inconsistent temperatures
• May illuminate a sensor-related error on models with diagnostics

• 1 outlet thermistor

• Disconnect power; shut off gas supply for gas models before servicing
• Access the exhaust/outlet duct or blower housing (location varies by model); the thermistor mounts on this duct
• Note wire locations, remove the fastener/clip, transfer any bracket if present, and install the new sensor with its tip in the airflow; secure connections
• Reassemble and run a test cycle to proper heat cycling

The Motor Drive is an OEM part for GE dryers. It contains the electronic speed control board which regulates the power delivered to the dryer motor and drum. This precise control is crucial for properly tumbling and circulating heated air through clothes loads during dry cycles. 

Causes of a bad motor drive can include normal wear and tear over extended use, water or moisture damage corroding electronic components, or failure of individual parts such as capacitors or microchips.

Symptoms include:

• The dryer drum failing to rotate or tumble clothes
• Abnormal sounds, smells or heat coming from the motor 
• Cycles failing to initiate, complete, or progress properly
• Fault codes displayed or electrical issues

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Proper operation of the motor drive helps ensure safe, dependable performance from your dryer.

This pulley nut secures the washer's drive pulley to the shaft to keep the belt aligned and power transfer reliable. Replacing a worn or missing nut restores stable spin performance and helps prevent belt slippage and noise.

• Locks the drive pulley to the shaft for proper belt alignment and consistent power transfer
• A loose or stripped nut can cause pulley wobble, belt squeal, slippage, or the belt coming off
• Replace if the original nut is damaged, missing, or will not stay tight after adjustment

• Disconnect power and water supply; safely tip or elevate the washer for bottom access
• Remove the drive belt; hold the pulley while loosening the nut (verify thread direction—do not force)
• Hand-start the new nut to avoid cross-threading; tighten securely per service information and confirm pulley runs true
• Reinstall the belt, verify alignment, and rotate by hand before restoring power

The Idler Arm is an OEM component specifically designed for GE dryers. It is a vital part that helps transfer power from the motor to the tumbling action of the dryer drum. The idler arm assembly allows the belt to provide smooth, consistent power to operate the drum efficiently during each cycle.  

Symptoms of a bad idler arm assembly include:

• Squealing or grinding noises coming from the dryer motor or drum area
• The dryer drum not rotating or spinning slowly
• Loose, cracked, or worn idler pulley
• A worn or slipping dryer belt 

Causes of failure can be normal wear and tear over extended use. Excess vibration from an unbalanced load or a dropped object inside the dryer could also potentially damage the idler arm.

This part is compatible with Hotpoint, RCA, and Kenmore dryer models.

The Igniter is an OEM part for GE dryers. This part is responsible for generating a spark or glow that ignites the gas, producing the necessary heat to dry your clothes effectively. It ensures that the dryer reaches and maintains the desired temperature throughout the drying cycle.

A bad igniter can occur due to wear and tear, electrical malfunctions, or damage from excessive heat. If you notice symptoms such as the dryer not heating up, a lack of heat during the drying cycle, or the burner not igniting, it may be time to replace this part.

Symptoms of a bad igniter include:

• Dryer not heating up
• Lack of heat during the drying cycle
• Burner not igniting

Restore your GE dryer by replacing the faulty igniter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Hi-Limit Thermostat is an OEM part for GE dryers. As a dryer's primary temperature control component and safety switch, it monitors heat levels during cycles. The thermostat is designed to automatically cut power if temperatures exceed safe limits, preventing potential fire hazards. 

Causes of a bad thermostat can include normal wear over time, prolonged exposure to high heat, electrical faults, or physical damage. Failure to properly vent a gas dryer could also overload the thermostat.

Symptoms of a bad thermostat include:

• The dryer failing to operate as intended or prematurely ending cycles  
• Overheating issues like unusual smells or visible damage
• Inaccurate temperature readings that impact drying performance

This OEM GE replacement ensures the dryer's temperature control and safety mechanism function properly. It is compatible with some Hotpoint, RCA, and Kenmore dryer models. Replacing a faulty thermostat helps avoid potential risks from excessively high dryer temperatures.

This inlet backup thermostat is the dryer's safety temperature control at the air inlet. It opens the heater circuit if temperatures rise too high, helping protect the unit and maintain safe, consistent drying performance.

• Monitors inlet air temperature and acts as a safety cutoff for the heater circuit
• Helps maintain proper drying temperatures and protect internal components from overheating
• Failure can cause little or no heat or inconsistent heat
• Contribute to long dry times or the dryer shutting off on over-temperature

• Disconnect power before service; if gas, also shut off the gas supply
• Access the inlet duct area per your model's service information
• Note wire positions and transfer them one at a time to the new thermostat
• Ensure the thermostat mounts flush to the duct; clean lint screen, interior, and exhaust vent to restore airflow