Jenn-Air 88891 Cooktop Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP707929
Traps grease and particles from cooking to maintain efficient ventilation. Replace every 6-12 months depending on usage. Confirm fit with your model number.
This part fixes the following symptoms
-
Touchpad does not respond
See more...
Do-It-Yourself Stories from Customers like You
Parts needed replacement Maria C. • Spring Hill , FL • September 07, 2015
Ordered all the parts needed, replaced them and the Jenn Air worked just fine.
Read more
More
$28.43
- Compare At:
-
$33.55
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 700855K
Fix burners that won't turn on or heat up with this burner switch kit. Includes mounting hardware and instructions. Easy 30-minute DIY repair.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The burner switches were not controlling the burners correctly specifically the lo temps were too high the switch knobs were also worn Frank C. • Sunset Beach , NC • December 24, 2019
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.)
The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one...
Read more
More
$84.40
- Compare At:
-
$100.44
- You Save:
-
$16.04
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY700854
Replace worn, cracked, or faded burner control knobs on your cooktop. Restores clear temperature markings and secure grip for adjusting heat settings.
Do-It-Yourself Stories from Customers like You
The burner switches were not controlling the burners correctly specifically the lo temps were too high the switch knobs were also worn Frank C. • Sunset Beach , NC • December 24, 2019
1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.)
The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one...
Read more
More
$25.76
- Compare At:
-
$30.40
- You Save:
-
$4.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP179051
Replacement 10-32 machine screw for securing panels, brackets, and internal components. Ideal for replacing missing, stripped, or damaged hardware.
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$7.94
- Compare At:
-
$8.90
- You Save:
-
$0.96
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$21.46
- Compare At:
-
$25.54
- You Save:
-
$4.08
Genuine Whirlpool part
By: Whirlpool
Part Number: 707704K
Fix a downdraft fan that stops working, vibrates excessively, or cycles on and off. This blower motor replacement takes 1-2 hours to install.
Do-It-Yourself Stories from Customers like You
Stove downdraft stopped working Robert B. • Gaithersburg , MD • March 08, 2016
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business.
Read more
More
$241.49
- Compare At:
-
$287.37
- You Save:
-
$45.88
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY708730
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
- Creates a fixed, insulated junction between external supply wires and internal appliance wiring
- Maintains tight screw-lug connections to minimize resistance and heat buildup
- Helps ensure steady power delivery to controls, motors, and heaters
- Common indicators of failure: melted/discolored block, burning odor, visible arcing, loose or stripped terminals, intermittent or no power
What's included: 1 terminal block Install notes:
- Disconnect power at the breaker and verify zero voltage before servicing
- Photograph/label wire positions; transfer one lead at a time to the new block
- Tighten terminal screws firmly; do not overtighten into the insulator
- Inspect wire ends/ring terminals and strain relief; replace any heat-damaged components per the service information
Do-It-Yourself Stories from Customers like You
Old and rusting Edwin H. • Corpus Christi , TX • December 14, 2016
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat.
Read more
More
$53.21
- Compare At:
-
$63.32
- You Save:
-
$10.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY707985
This is a blower wheel used in the downdraft exhaust ventilation system of a range or cooktop. It mounts on the motor shaft and draws smoke, steam, and cooking odors down and out through the vent ductwork. Replace this part if the exhaust fan is noisy, vibrating excessively, or not moving air effectively despite the motor running.
Do-It-Yourself Stories from Customers like You
Stove downdraft stopped working Robert B. • Gaithersburg , MD • March 08, 2016
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business.
Read more
More
$94.67
- Compare At:
-
$112.66
- You Save:
-
$17.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP71003558
This motor isolator is a vibration-damping grommet that cushions the motor mount to reduce noise and prevent metal-to-metal contact. Replacing worn isolators helps keep the motor seated correctly and the appliance running quieter and smoother.
- Cushions the motor to minimize vibration transfer to the chassis
- Helps reduce rattling or buzzing noises during fan/blower operation
- Supports proper motor alignment and mounting stability
- A common maintenance item when rubber mounts become cracked, hardened, or missing
What's included: One motor isolator grommet Install notes:
- Disconnect power and allow hot components to cool before service
- Access the motor mounting points; replace isolators in matched locations
- Inspect adjacent mounts and hardware; replace additional isolators as needed
- Do not overtighten fasteners—compress the grommet evenly without deforming it
Do-It-Yourself Stories from Customers like You
The exhaust fan was clunking so took it apart and one isolator came off Lloyd L. • Fort Mill , SC • September 13, 2014
Ordered three isolators and changed all of them. Sounds like new.
Read more
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489128
$9.05
- Compare At:
-
$9.38
- You Save:
-
$0.33
Genuine Whirlpool part
By: Whirlpool
Part Number: WP59002061
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
Do-It-Yourself Stories from Customers like You
Burners would not light Michael C. • Bastrop , LA • August 08, 2024
Replaced burners and cleaned
Read more
More
$7.56
- Compare At:
-
$8.32
- You Save:
-
$0.76
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3188425
Gas valve shaft seal.
Do-It-Yourself Stories from Customers like You
Shorted igniter switch and one missing ignitor shaft seal Michael M. • San Diego , CA • August 07, 2015
I replaced the igniter harness and the missing igniter shaft seal with parts from appliancepartspros.com
Read more
More
$50.57
- Compare At:
-
$60.18
- You Save:
-
$9.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY707702
This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:
- Secures shafts, pulleys, or fittings to prevent axial movement
- Keeps assemblies fastened under normal vibration and load
- Helps stop wobble, grinding, or part separation caused by a loose connection
- Works with the matching threaded stud, shaft, or fitting for a proper hold
What's included: One locknut Install notes:
- Disconnect power and follow appliance safety procedures before servicing
- Use the matching thread size and engage threads fully; hand-start before tightening
- Tighten securely without overtightening; use the correct driver or socket for the nut
- Inspect mating threads and replace if damaged
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: Y708862
Stamped metal retaining clip that secures screws to panels and trim. Replace if clip is bent, broken, or missing to properly fasten covers and components.
More
$8.95
- Compare At:
-
$11.08
- You Save:
-
$2.13
Genuine Samsung part
By: Samsung
Part Number: DE81-03521A
This burner ring cap base provides the support and alignment for a gas cooktop burner cap, helping direct the flame for consistent heating and safe operation. It replaces damaged or warped bases that prevent proper burner seating. What it does:
- Supports and centers the burner cap so the flame is properly directed
- Restores even heating and stable flame pattern when the original base is cracked or warped
- Helps maintain correct burner-to-cap spacing for reliable ignition and simmer control
- Prevents burner cap wobble that can cause uneven cooking or noisy flames
What's included: One burner ring cap base Install notes:
- Turn off the gas supply and power to the appliance before starting any work
- Remove burner cap and grate to access the base; ensure all surfaces are clean and dry before installing
- Fit the new base into the burner assembly and ensure the cap seats evenly and securely
More
$229.97
- Compare At:
-
$258.03
- You Save:
-
$28.06
Genuine Samsung part
By: Samsung
Part Number: DE81-05803A
$158.29
- Compare At:
-
$172.07
- You Save:
-
$13.78