Kanmore Range Hood Model 233052345590 Parts

Replaces a cracked, broken, or missing refrigerator door bin tray. Restores secure storage for bottles and items in the door compartment.

Rubber foot that cushions and stabilizes your refrigerator, preventing sliding and surface scratches. Replace if worn, cracked, or missing.

Reduces chlorine, sediment, lead, and mercury from drinking water. Replace every 6 months or 400 gallons for optimal performance. Verify fit with model.

Supports the refrigerator door hinge for smooth, quiet opening and proper alignment. Replace if door catches, squeaks, or binds. Verify fit with your model.

This motor drives the evaporator fan that circulates cold air from the evaporator coils throughout the freezer and refrigerator compartments. It is typically mounted near the evaporator coils inside the freezer section. Replace this motor if you hear loud buzzing or grinding noises from the freezer, or if the refrigerator is not cooling properly despite the compressor running.

Fix a warm fridge or freezer alarm with this temperature sensor. Replaces faulty thermistors causing incorrect temperature readings and food spoilage.

Fix poor cooling and noisy operation with this refrigerator fan motor. Restores proper air circulation when your fridge isn't cooling evenly or runs loud.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

Replacement mounting screw for refrigerator panels, brackets, and trim. Secures loose components and restores proper alignment. Direct-fit fastener.

This drain gutter is the molded channel that collects and directs wash water toward the dishwasher drain, helping prevent pooling at the tub base and under the door. It restores proper water flow inside the lower tub area. What it does:

• Channels leftover wash and condensation to the pump/drain to avoid water buildup under the door
• Helps reduce leaks and water pooling at the bottom front of the tub
• Replaces cracked or warped gutters that cause misdirected drainage or visible water inside the door area
• Matches OEM shape so water follows the intended path to the drain system

• One drain gutter

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door or lower access panel per the service instructions to reach the gutter
• Handle carefully to avoid damage to the molded edges and to prevent contact with sharp cabinet or panel edges
• Secure mounting so the gutter seats fully to the tub and mates properly with adjacent seals

The adjusting screw allows you to level your refrigerator and adjust door alignment, typically located at the base of the unit. Replace when the screw becomes stripped, corroded, or can no longer properly support or adjust the refrigerator.

This door seal fits around the dishwasher tub opening to keep water and steam inside during cycles. Replacing a worn gasket restores a tight seal so the door latches properly and helps prevent leaks at the sides or bottom.

• Creates a watertight barrier between the door and tub during wash and rinse cycles
• Helps contain steam and reduce moisture escaping from the front of the unit
• Replaces a flattened, cracked, torn, or deformed seal that can cause leaks
• Common symptoms include drips at the front edge, water on the floor near the door, and needing extra force to latch

• Disconnect power and, if applicable, shut off the water supply before servicing
• Pull the old seal from the channel; clean the groove and mating surfaces thoroughly
• Press the new seal in evenly without stretching; seat corners fully and position the joint at the bottom center
• Close the door to help the seal set; a snug fit at first is normal

This is a flexible rubber seal that attaches around the perimeter of the freezer door, creating an airtight closure when the door is shut. It prevents warm air from entering the freezer compartment and keeps cold air from escaping. Replace this gasket if you notice frost buildup inside the freezer, the door does not seal tightly, the gasket is torn or warped, or the compressor runs more frequently than normal.

Replacement freezer storage tray for your refrigerator. Installs inside the freezer compartment to organize and store frozen items. Order now if cracked or broken.

Replacement mounting screw for refrigerators. Secures panels, trim, and internal components. Needed when original screw is missing, stripped, or damaged.