Speedqueen Awn432sp113tw01 Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This dual water inlet valve kit controls the hot and cold water entering select top-load washers. Replacing a weak or leaking valve restores proper fill performance and helps prevent slow fills, wrong temperatures, and unwanted drips.

• Regulates hot and cold water flow into the tub during fill cycles
• Integrated inlet screens help trap debris from the water supply
• Failure can cause no fill, slow fill, incorrect temperature, continuous filling, or water seeping into the tub when off

• Disconnect power and turn off both water supplies before servicing
• Place towels and a container to catch residual water; relieve pressure at the hoses
• Note and transfer hose and wire connections one-for-one to the new valve
• Restore water and power, run a test fill, and check for leaks

This dual water inlet mixing valve controls and blends the hot and cold supply during the fill cycle. Replacing a failing valve restores proper fill rate and water temperature selection for consistent wash performance.

• Opens and closes to admit hot and cold water as directed by the control, creating the selected temperature
• Helps maintain proper flow to the tub/dispenser during fill
• Common failure symptoms: no fill or slow fill, incorrect water temperature during fill, water continuing to drip or flow into the tub when the machine is off, or leaks from the valve body
• Humming from the valve with little or no water flow due to internal failure or clogged screens

• Disconnect power and shut off both water supplies before servicing; relieve line pressure
• Place towels, disconnect hoses, and note hot/cold orientation; inspect/clean inlet screens
• Transfer any brackets/fittings from the old valve if required; connect hoses securely without overtightening
• Turn water back on, check for leaks, then run a fill test to verify operation

The Idler Lever Kit is an OEM replacement part for Speed Queen dryers. This kit includes the idler lever, which plays a key role in maintaining proper tension on the dryer drum belt. By ensuring the belt stays aligned and taut, the idler lever enables smooth drum rotation during the drying cycle.

Symptoms of a bad Idler Lever Kit include:

• A squealing or screeching noise during dryer operation
• The drum not spinning or rotating properly
• The belt appearing loose or slipping off the pulley

Causes of a failing Idler Lever Kit can include normal wear and tear over time, damage from excessive strain or overloading, or misalignment of the drum or belt.

This OEM Speed Queen part is also compatible with Alliance laundry equipment.

This Washer Lid is an OEM replacement part for Speed Queen washers. It serves as the main cover and provides access to load and unload clothes during washing and rinsing cycles. The lid must be sealed tightly to minimize noise and ensure optimal energy efficiency.

Causes of a bad lid include long-term exposure to heat and moisture during use, impact or other physical damage.

Symptoms of a bad lid include:

• Excessive noise during spinning or agitation cycles
• Long wash times and higher energy bills due to leaks
• Difficulty opening or closing the lid securely
• Warping or bulging appearance

This OEM Speed Queen part is also compatible with American Dryer Corporation and Continental clothes washers.

The Drain Pump is an OEM part for Speedqueen brand washing machines. Located near the rear of the washer tub, the drain pump works to empty water from the machine at the end of each cycle. It functions through an electrical motor that activates a spinning impeller, forcing water through the drain hose. 

Symptoms of a bad drain pump include:

• Washer fails to fully drain or leaves standing water 
• Drain cycle takes an unusually long time to complete
• Loud grinding or rattling sounds coming from inside

Over time, a buildup of lint or mineral deposits inside the pump chamber can clog the impeller and reduce efficiency. Allowing water to sit for extended periods also promotes mold growth. Replace your drain pump today with this genuine Speedqueen part and restore full draining capability.
 

The Pressure Sensor is an OEM part for Speedqueen commercial washers. It plays an important safety role by actively monitoring water levels and pressure changes within the washing machine. Located internally, the sensor communicates water level status to the control module.

Causes of a bad pressure sensor can include failure or degradation of electronic components over time. Damage from impact or liquid ingress may also cause sensors to malfunction.

Symptoms of a bad Pressure Sensor include:

• Erratic or inconsistent water levels during fills and drains
• Inability to detect rises or falls in water pressure
• Fault codes or error messages on the control panel
• Safety issues from unregulated water valves

This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.

This kit replaces the washer's pump and its belt on Model M designs, restoring dependable water removal and belt-driven operation. Install it to address leaks, seized pumps, or a worn/broken belt causing drain or spin complaints.

• Moves wash water out of the tub during drain cycles via the replacement pump
• Replaces the belt that drives the pump in belt-driven systems
• Can help with symptoms such as won't drain, slow draining, leaks at the pump, belt squeal, or a burned-rubber smell
• Restores smooth belt-to-pulley operation when the original pump is binding or the belt is frayed/broken

• Disconnect power and water supplies before servicing; allow the unit to cool
• Place towels or a catch pan; clamp hoses before removing the pump to limit spills
• Note belt routing; install the new belt on clean, oil-free pulleys and alignment
• After installation, check for leaks and proper drain operation

Note: DO NOT use any sealant other than 200996P Sealant.

This upper and lower bearing set supports the rotating shaft assembly, helping it turn smoothly and quietly. Replacing worn bearings reduces noise and vibration and protects adjacent components from accelerated wear. What it does:

• Provides radial support so the shaft/drum rotates freely with minimal friction
• Worn bearings can cause rumbling, squealing, or grinding during operation
• Can show play at the shaft or metallic dust near the bearing area

What's included:

• 1 bearing

Install notes:

• Disconnect power and shut off water/gas before servicing
• Access the bearing housing; use a press or proper driver to remove/install bearings—do not strike the races
• Note bearing orientation and seating depth; install squarely and fully
• Inspect the shaft and any related seals/housings and replace if worn or damaged

This idler pulley wheel keeps the drive belt aligned and under constant tension so the drive system runs smoothly and quietly. Replacing a worn wheel helps eliminate belt squeal and prevents premature belt wear or slippage.

• Maintains proper belt tension on the idler arm and guides the belt during operation
• Provides low-friction rotation for smooth belt tracking
• Common symptoms of a worn wheel: squealing/squeaking, frayed or glazed belt, belt slipping off, or intermittent/no drive
• Helps restore reliable belt traction and reduce noise

• Disconnect power and wear work gloves before servicing
• Access the drive system and note the belt routing for reassembly
• Release belt tension, remove retaining hardware, swap the wheel on the idler arm, and re-tension the belt
• Spin the new wheel by hand to inspect belt and idler arm/spring and replace if worn

This timer knob assembly replaces a worn or broken control knob so you can confidently select and adjust cycles. A fresh knob restores a positive grip on the timer shaft and smooth, accurate operation.

• Mounts on the timer shaft to turn and set cycle selection and time
• Restores secure engagement when the original knob is cracked, stripped, loose, or missing
• Helps ensure the timer turns when you rotate the knob
• Common symptoms: knob spins without engaging, difficult to set cycles, visible damage

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft; avoid prying that could damage the control
• Align the new knob with the shaft (flat/D-shape) and press until fully seated
• If the original used a small insert or spring clip, transfer it to the new knob if needed

Replacement timer that controls the washer's cycle sequencing and timing, restoring reliable wash/rinse/spin transitions on compatible commercial/top-load machines. Installs at the control panel to regain proper automatic cycle progression. What it does:

• Advances the washer through timed wash, rinse and spin steps for 4-cycle machines.
• Routes power to motors, valves and switches at the correct points in each cycle.
• Common symptoms: machine won't advance through cycles, stops mid-cycle, or exhibits inconsistent timing.
• Electromechanical control designed for direct swap with matching timer assemblies.

• Always disconnect power at the breaker before servicing the washer.
• Photograph wiring and connector locations before removal to ensure correct reassembly.
• Handle the control shaft and wiring harness carefully to avoid bending cams or damaging terminals.
• Restore power and test cycles after installation.

The Aluminum Pulley Kit is an OEM component specifically designed for Speed Queen commercial washers. This kit includes both an aluminum pulley and the necessary shaft and hardware for proper installation. 

The pulley works with the washer's transmission system to transfer rotational power to the internal drum and cabinet components. It allows for controlled, consistent movements throughout wash and spin cycles.

Symptoms of a bad pulley kit include: 

• Excessive vibration and noise during operation
• The washer fails to advance through cycles properly  
• Damage to belts or other transmission parts

Causes of pulley failure can be wear over time, cracks or warping of the aluminum from overheating, or damage from dropped loads that impact the pulley area.

This OEM Speed Queen replacement part is also compatible with Dexter, Huebsch, Milnor, and IPSO commercial washer models.
 

This timer skirt is the bezel that sits behind the timer knob on the control panel. It replaces a cracked or missing ring so you can securely turn the knob and select settings.

• Sits around the timer shaft as the cosmetic/structural ring behind the knob
• Supports and stabilizes the timer knob during setting selection
• Replaces a cracked, warped, or missing bezel that causes a loose or wobbly knob
• Typical symptoms include a broken ring, misaligned knob, or difficulty selecting settings

• Disconnect power before servicing
• Pull off the timer knob; remove any retaining clip or nut if present
• Remove the old skirt; align and seat the new skirt in the control panel
• Reinstall the knob and verify smooth operation