Ade4brgs176tw01 Parts

This 120V light housing assembly secures and protects the interior light in your machine, restoring dependable illumination inside the cabinet. It positions the bulb and socket correctly so you can clearly see the drum/compartment when the door opens.

• Mounts and insulates the interior light socket within the cabinet
• Positions the bulb for proper interior illumination
• Helps resolve issues from a cracked, heat-damaged, or loose housing
• Typical symptoms: interior light won't turn on, flickers intermittently, or only works when the door is moved
• Designed for 120V systems

• Disconnect power before servicing to avoid electrical shock
• Access the light area per your model's service information; remove panels as needed
• Note wire locations; make secure connections to the new housing
• Restore power and test the interior light before final reassembly

This 4-position fabric selector switch is the control behind the knob that sets your washer's fabric setting. Replacing a worn switch restores crisp detents and reliable selection so the machine follows the wash action you choose.

• Controls the washer's fabric setting with four selectable positions
• Directs electrical contacts to deliver the chosen wash action or speed
• Works with the timer/control to tailor cycle aggressiveness for different fabrics
• Symptoms of failure: settings don't change, only one position responds, wrong wash action, or the knob feels loose and won't detent

• Disconnect power before servicing; control panel edges can be sharp
• Remove the knob, then the retaining nut or clip to free the switch from the panel
• Photograph and label wires; transfer them one at a time to matching terminals on the new switch
• Align the shaft/indexing tabs, secure the switch, and test each position before reassembly

This moisture sensor base positions and secures the washer's moisture sensing contacts so the control can detect fabric dampness and finish cycles correctly. Restores reliable wetness detection when the original base is damaged or worn. What it does:

• Holds the moisture-sensing probes/contacts in the correct location for accurate wetness readings.
• Passes moisture detection signals to the control so automatic cycles advance and end properly.
• Helps address symptoms like inconsistent dryness, cycles that stop too soon or run too long, or error codes related to moisture sensing.
• Use when the mounting base is cracked, corroded, or connector fit is loose.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access typically requires removing the washer cabinet or access panels; keep fasteners and connectors organized.
• Handle sensor contacts carefully to avoid bending or contaminating the probe surfaces; ensure connectors are fully seated.

Dryers, washers, and washer dryer combos are made with an idler pulley shaft. It works in combination with the rest of the equipment in multiple ways. It switches the direction in which the output shaft is rotating. The idler pulley shaft also works to change gears and maintain the space between shafts. With time, because of excessive force, or as a result of misuse, the idler pulley shaft can wear out, break, or get damaged otherwise. When the part isn't working correctly, it has to be replaced to continue using the machine.The primary indication that there is something wrong with the idler pulley shaft is a machine that's producing excessive noises. Replacement of the idler pulley shaft is a straightforward process. It can be done in a few minutes with a nut driver and screwdrivers. Unplug the appliance before starting the disassembly.This idler pulley shaft is a genuine OEM replacement part. It is sold as an individual unit. It is made of durable metal materials. The idler pulley shaft is sourced from the manufacturer. It can be installed in various machines made by Speed Queen, Amana, and Magic Chef.

This appliance screw replaces a missing or damaged fastener to secure panels and brackets. With a 10B-16 thread and 0.34-inch length, it restores a tight fit to help reduce vibration, rattles, and loosening.

• Fastens sheet-metal parts, brackets, and covers in the appliance cabinet
• Helps maintain alignment and support of components subject to vibration
• Direct replacement for stripped, rusted, or missing hardware
• Can help resolve symptoms like loose panels, rattling noises, or gaps

• Disconnect power; shut off gas/water as applicable before servicing
• Start threads by hand in the original hole or clip to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping
• If the receiving clip/nut is damaged, repair or replace it for a secure hold

This wire organizer assembly secures and routes the wiring at the fabric selector to reduce wear and keep connections tidy for reliable machine operation. It helps prevent chafing, pinching, and loose harness routing that can cause intermittent issues. What it does:

• Holds and routes selector-area wiring to prevent rubbing and accidental disconnection
• Reduces risk of damaged insulation from contact with moving parts
• Keeps harnesses in the correct position for consistent electrical connections
• Helps maintain safe clearance between wires and metal edges or controls

• One wire organizer assembly for the fabric selector area

• Disconnect power to the appliance before servicing to avoid electrical shock
• Reference the machine's service manual or diagram for correct routing and clip orientation
• Replace any damaged clips or wiring and ensure the organizer snaps into factory mounting points
• Avoid pinching wires when reassembling panels and verify selector operation after installation

This is the rotating dryer cylinder assembly. Replacing a dented, rusted, or out-of-round cylinder restores smooth tumbling and helps prevent snags, noise, and uneven drying performance.

• Holds and tumbles laundry while working with the belt/drive system
• Internal white baffles lift and separate clothes for better airflow
• Smooth interior helps protect fabrics from catching or tearing
• Typical signs it's needed: loose or broken baffles, interior rust, dents, scraping/thumping once per revolution, or recurring fabric snags

• Disconnect power; for gas dryers, also shut off the gas supply
• Wear cut-resistant gloves—metal edges can be sharp
• Access typically requires removing the top/front panels and releasing belt tension; note belt routing
• Set drum, route belt correctly, spin by hand to confirm clearance, then reassemble and test

This blower housing seal restores a tight air path between the blower housing and its mating surface, keeping airflow directed through the drum and exhaust. Replacing a worn seal can improve drying performance and limit lint leakage inside the cabinet. What it does:

• Creates a tight seal at the blower housing to prevent air bypass and leaks
• Helps maintain designed airflow and drying efficiency
• Common signs of failure: longer dry times, weak airflow at the vent, lint/dust inside the cabinet, or visible wear/flattening of the seal
• Helps keep warm air and lint contained within the intended airflow path

• Includes 1 blower housing seal

• Disconnect power (and gas, if applicable) before servicing; allow the appliance to cool
• Access the blower housing, remove the old seal, and clean mating surfaces of lint and debris
• Fit the new seal evenly around the housing; avoid gaps, twists, or over-compression
• Reassemble and verify strong airflow at the exhaust; inspect and clean the venting as needed

This Rulon 488 cylinder glide supports the front edge of the dryer drum at the bulkhead. Replacing a worn glide restores smooth, quiet rotation and helps eliminate scraping or squealing from the front of the drum.

• Provides a durable, low-friction surface between the drum rim and front bulkhead
• Supports the drum to minimize drag and wear for quieter operation
• Worn glide may cause scraping/squealing noises or a dragging drum
• Visible flat spots, grooves, or excessive wear on the glide indicate replacement

• Disconnect power and shut off gas supply before servicing
• Access the front bulkhead and support the drum to relieve load on the glide
• Remove the worn glide and clean the mounting area; install the new glide in the same position/orientation per factory fasteners
• Rotate the drum by hand to inspect felt seals and any additional glides and replace if worn

This Dryer Output Control Assembly is the electronic board that directs power to the dryer's major components. Replacing a failing board restores reliable motor, heat, and auxiliary output control for consistent cycle operation.

• Routes power from the control system to key loads such as the drive motor, heater, and other output devices
• Helps coordinate starting, running, heating, and timed functions during a cycle
• Failure symptoms include: dryer won't start, no heat, won't tumble, intermittent or erratic operation, or error codes

• Disconnect power before servicing; verify no power is present
• Use ESD protection; handle the board by edges and avoid touching components
• Transfer and seat all wire connectors one at a time; photograph/label before removal
• Secure the board and recheck connections before restoring power and testing

This dryer output control kit replaces the dryer's output-control assembly to restore correct electronic signaling and normal cycle operation. Use it to address intermittent starts, unexpected stops, or cycles that end prematurely. What it does:

• Replaces the dryer's output-control assembly to restore proper output signaling between components.
• Helps correct intermittent operation, failure to start, unexpected shutdowns, or incorrect cycle termination.
• Restores worn or damaged control hardware so the dryer can complete selected cycles.

• Disconnect electrical power (and turn off gas supply for gas dryers) before beginning any work.
• Handle electronic components carefully and avoid static discharge; do not force connectors.
• Follow OEM wiring and mounting orientation exactly; tight mounting prevents misalignment and noise.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

This felt pad cushions and isolates contact points inside the machine to reduce metal-to-metal contact, noise, and wear. Replace a worn or missing pad to help restore smoother, quieter operation and protect mating surfaces. What it does:

• Provides a soft, low-friction barrier between contacting parts
• Helps prevent squeaking, scraping, or rattling during operation
• Reduces wear at the specified contact point to protect components
• Visible thinning, glazing, or a missing pad can lead to noise and accelerated wear

• 1 felt pad

• Disconnect power (and gas/water, if applicable) before servicing
• Remove the old pad and clean the surface; align the new pad with the original footprint
• If adhesive-backed, apply to a clean, dry surface; reassemble and test for proper operation

This resistor assembly is a direct replacement electrical component that restores proper resistance in the appliance's control circuit, helping restore reliable operation and electrical continuity where the original resistor has failed. What it does:

• Provides the correct resistance in the control/electrical circuit so related components operate as designed
• Commonly replaces a failed or open resistor causing intermittent operation or control faults
• Can help stop symptoms such as erratic cycles, failure to start, or control-board error indications tied to resistance faults
• Works as a like-for-like replacement when the original resistor assembly is damaged or shows out-of-spec resistance

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the assembly carefully and avoid touching contact surfaces; observe ESD precautions if present
• Verify connector fit and secure all fasteners; confirm correct orientation before re-applying power

Adjustable 120V buzzer that restores audible cycle alerts on laundry equipment. Replaces failed or weak buzzers so you can hear end-of-cycle and warning signals clearly. What it does:

• Produces audible beeps/tones to indicate cycle completion and alert conditions.
• Adjustable design lets the buzzer be tuned to match the original unit's audible output.
• Common replacement when the machine is silent at the end of a cycle, emits intermittent beeps, or has a weak/no buzzer sound.
• Designed for use in 120V household laundry appliances requiring an adjustable buzzer.

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Remove the old buzzer, transfer mounting hardware, and connect wires to matching terminals; maintain original wire routing.
• Restore power and run a test cycle to audible operation and proper adjustment.

This motor pulley is the drive pulley for 60 Hz Speed Queen washers, transferring motor rotation to the drive system so the washer can spin and agitate normally. It's a direct-fit replacement that restores proper belt engagement. What it does:

• Fits onto the washer motor shaft and redirects power to the drive belt and transmission
• Restores normal spin and agitation when a worn or damaged pulley causes slipping or loss of drive
• Helps eliminate belt misalignment, squealing, or irregular drum movement related to pulley wear
• Works with the motor assembly to maintain correct belt routing and tension

• One motor pulley (60 Hz)

• Disconnect power to the appliance before starting any work
• Support the drum and relieve belt tension before removing the old pulley
• Verify correct pulley seating on the motor shaft and proper belt alignment during reassembly
• Torque to OEM specs; replace any damaged fasteners