Ade8060 Parts

Cushions drum contact points to reduce noise and metal wear in your dryer. Replace when worn, torn, or missing to restore quiet operation. Confirm fit with your model number.

Specs: No.8X1/2 HEX WASHER HEAD

This retaining ring secures a component on a shaft or within a groove so it stays aligned during operation. Replacing a bent, rusted, or missing ring helps stop wobble, noise, and parts working loose.

• Locks into a groove to keep gears, pulleys, wheels, or spacers from sliding off a shaft
• Helps maintain proper spacing and alignment of moving parts
• Common signs of failure: wobbling parts, scraping/rubbing noises, or components that work loose
• Visual clues: deformation, corrosion, or loss of spring tension

• Disconnect power and any utilities to the appliance before service
• Wear eye protection—retaining rings can spring free under tension
• Note the order/orientation of any washers or spacers before removal
• Use appropriate snap-ring or needle-nose pliers and ensure the ring seats fully in its groove

Screw: 8-16 x 3/8 inch.

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

If your dryer is vibrating excessively or making loud thumping noises, a worn drum roller bracket may be the cause. This bracket restores smooth rotation.

Can't hear when your dryer cycle ends? This buzzer restores audible end-of-cycle alerts and warning signals. Adjustable volume, easy installation.

This left-side white panel end replaces a damaged or worn corner trim on the control console or front fascia to restore appearance and protect edges. Designed to match original fit and finish on compatible Speed Queen units. What it does:

• Covers and protects the left edge of the console/front panel from bumps, wear, and moisture.
• Restores a clean, finished look when the original panel end is cracked, chipped, or missing.
• Helps maintain proper alignment and support for adjacent trim and fasteners.
• Fits in place of the factory left-side panel end for straightforward cosmetic repair.

• Designed for direct replacement; reinstall using original screws/clips when present.
• Inspect adjacent trim and fasteners; replace any damaged clips to ensure secure fit.
• Power down and unplug the appliance before attempting any repairs that require panel removal.

Secures internal components inside your dryer cabinet. Replace if bent, cracked, stripped, or missing to restore proper alignment and stability.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

This 12-14 x 1/2 screw is a factory fastener used to secure appliance panels, brackets, and components. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and keeps parts properly aligned for reliable operation.

• Secures panels, brackets, and internal components to their mounting points
• Replaces damaged, rusted, or missing hardware
• Helps stop vibration and rattling caused by loose fasteners
• Restores proper alignment and stability of covers or assemblies

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the original screw's location and length; replace one at a time
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Reinstall any original washers, clips, or spacers used with the screw

Size: 10-32

Note: This part is one screw, order quantity needed.

This front bulkhead assembly replaces the washer's front tub support and splash barrier, restoring proper drum alignment and helping prevent leaks. Built as a service-pack replacement to fit factory mounting points and finishes. What it does:

• Supports and aligns the washer drum and outer tub for smooth spinning
• Forms a splash barrier to help keep water inside the tub and away from controls
• Provides the factory mounting surface for door seal, bearing, and related components
• Helps reduce vibration caused by misaligned or damaged bulkheads

• Disconnect power and water supply before starting any repairs
• Drain the washer and remove the front panel or cabinet to access the bulkhead
• Keep track of gaskets, seals, and fasteners; replace any worn seals to prevent leaks

Replace your dryer door seal to prevent heat loss, contain lint, and restore efficient drying. Fits multiple models. Confirm compatibility before ordering.

Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.