Adee9rgs175w01 Parts

This appliance screw replaces a missing or damaged fastener to secure panels and brackets. With a 10B-16 thread and 0.34-inch length, it restores a tight fit to help reduce vibration, rattles, and loosening.

• Fastens sheet-metal parts, brackets, and covers in the appliance cabinet
• Helps maintain alignment and support of components subject to vibration
• Direct replacement for stripped, rusted, or missing hardware
• Can help resolve symptoms like loose panels, rattling noises, or gaps

• Disconnect power; shut off gas/water as applicable before servicing
• Start threads by hand in the original hole or clip to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping
• If the receiving clip/nut is damaged, repair or replace it for a secure hold

This is the rotating dryer cylinder assembly. Replacing a dented, rusted, or out-of-round cylinder restores smooth tumbling and helps prevent snags, noise, and uneven drying performance.

• Holds and tumbles laundry while working with the belt/drive system
• Internal white baffles lift and separate clothes for better airflow
• Smooth interior helps protect fabrics from catching or tearing
• Typical signs it's needed: loose or broken baffles, interior rust, dents, scraping/thumping once per revolution, or recurring fabric snags

• Disconnect power; for gas dryers, also shut off the gas supply
• Wear cut-resistant gloves—metal edges can be sharp
• Access typically requires removing the top/front panels and releasing belt tension; note belt routing
• Set drum, route belt correctly, spin by hand to confirm clearance, then reassemble and test

This blower housing seal restores a tight air path between the blower housing and its mating surface, keeping airflow directed through the drum and exhaust. Replacing a worn seal can improve drying performance and limit lint leakage inside the cabinet. What it does:

• Creates a tight seal at the blower housing to prevent air bypass and leaks
• Helps maintain designed airflow and drying efficiency
• Common signs of failure: longer dry times, weak airflow at the vent, lint/dust inside the cabinet, or visible wear/flattening of the seal
• Helps keep warm air and lint contained within the intended airflow path

• Includes 1 blower housing seal

• Disconnect power (and gas, if applicable) before servicing; allow the appliance to cool
• Access the blower housing, remove the old seal, and clean mating surfaces of lint and debris
• Fit the new seal evenly around the housing; avoid gaps, twists, or over-compression
• Reassemble and verify strong airflow at the exhaust; inspect and clean the venting as needed

This Rulon 488 cylinder glide supports the front edge of the dryer drum at the bulkhead. Replacing a worn glide restores smooth, quiet rotation and helps eliminate scraping or squealing from the front of the drum.

• Provides a durable, low-friction surface between the drum rim and front bulkhead
• Supports the drum to minimize drag and wear for quieter operation
• Worn glide may cause scraping/squealing noises or a dragging drum
• Visible flat spots, grooves, or excessive wear on the glide indicate replacement

• Disconnect power and shut off gas supply before servicing
• Access the front bulkhead and support the drum to relieve load on the glide
• Remove the worn glide and clean the mounting area; install the new glide in the same position/orientation per factory fasteners
• Rotate the drum by hand to inspect felt seals and any additional glides and replace if worn

This Dryer Output Control Assembly is the electronic board that directs power to the dryer's major components. Replacing a failing board restores reliable motor, heat, and auxiliary output control for consistent cycle operation.

• Routes power from the control system to key loads such as the drive motor, heater, and other output devices
• Helps coordinate starting, running, heating, and timed functions during a cycle
• Failure symptoms include: dryer won't start, no heat, won't tumble, intermittent or erratic operation, or error codes

• Disconnect power before servicing; verify no power is present
• Use ESD protection; handle the board by edges and avoid touching components
• Transfer and seat all wire connectors one at a time; photograph/label before removal
• Secure the board and recheck connections before restoring power and testing

This dryer output control kit replaces the dryer's output-control assembly to restore correct electronic signaling and normal cycle operation. Use it to address intermittent starts, unexpected stops, or cycles that end prematurely. What it does:

• Replaces the dryer's output-control assembly to restore proper output signaling between components.
• Helps correct intermittent operation, failure to start, unexpected shutdowns, or incorrect cycle termination.
• Restores worn or damaged control hardware so the dryer can complete selected cycles.

• Disconnect electrical power (and turn off gas supply for gas dryers) before beginning any work.
• Handle electronic components carefully and avoid static discharge; do not force connectors.
• Follow OEM wiring and mounting orientation exactly; tight mounting prevents misalignment and noise.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

This felt pad cushions and isolates contact points inside the machine to reduce metal-to-metal contact, noise, and wear. Replace a worn or missing pad to help restore smoother, quieter operation and protect mating surfaces. What it does:

• Provides a soft, low-friction barrier between contacting parts
• Helps prevent squeaking, scraping, or rattling during operation
• Reduces wear at the specified contact point to protect components
• Visible thinning, glazing, or a missing pad can lead to noise and accelerated wear

• 1 felt pad

• Disconnect power (and gas/water, if applicable) before servicing
• Remove the old pad and clean the surface; align the new pad with the original footprint
• If adhesive-backed, apply to a clean, dry surface; reassemble and test for proper operation

This motor pulley is the drive pulley for 60 Hz Speed Queen washers, transferring motor rotation to the drive system so the washer can spin and agitate normally. It's a direct-fit replacement that restores proper belt engagement. What it does:

• Fits onto the washer motor shaft and redirects power to the drive belt and transmission
• Restores normal spin and agitation when a worn or damaged pulley causes slipping or loss of drive
• Helps eliminate belt misalignment, squealing, or irregular drum movement related to pulley wear
• Works with the motor assembly to maintain correct belt routing and tension

• One motor pulley (60 Hz)

• Disconnect power to the appliance before starting any work
• Support the drum and relieve belt tension before removing the old pulley
• Verify correct pulley seating on the motor shaft and proper belt alignment during reassembly
• Torque to OEM specs; replace any damaged fasteners

This bracket is the mounting base for the dryer's cylinder support roller. Replacing a bent or worn bracket restores proper roller alignment so the drum turns smoothly, reducing vibration and noise and preventing premature wear.

• Provides the fixed mount for the cylinder support roller
• Maintains drum alignment for smooth, even rotation
• Replace if the bracket is bent, cracked, or mounting holes are elongated
• Common symptoms of a failing bracket: loud rumbling/thumping, scraping, excessive vibration, or visible roller misalignment

• Disconnect power; for gas models, also shut off gas supply
• Access the roller area per your model's service information and support the drum
• Transfer the roller/axle and spacers from the old bracket; install the new bracket in the same orientation
• Verify the roller spins freely and hand-rotate the drum to check for binding before test run

A replacement self-tapping screw used to secure plastic trim and sheet-metal panels on laundry equipment. Durable washer-head design helps distribute load and resist pull-through in plastic mounting points. What it does

• Fastens panels, trim pieces, and components where a short sheet-metal screw is required
• Self-tapping tip forms threads in plastic or thin metal for a secure hold
• Washer-style head spreads clamping force to reduce damage to plastic parts
• Common repair for missing, stripped, or broken mounting screws that cause loose panels or rattling

• One self-tapping screw (12-16 x 0.562 in) with hex washer head

• Use the correct screwdriver or low-torque driver to avoid over-tightening into plastic
• Start by hand-threading, then finish with short, controlled driver pulls
• Disconnect power and follow all safety guidance for the appliance before servicing
• Replace any damaged mating threads or inserts to ensure a secure repair

This washer cylinder baffle mounts to the inner basket and lifts garments as the basket turns. Replacing a cracked, loose, or missing baffle restores proper turnover, reduces banging noises, and helps prevent fabric snags.

• Lifts and tumbles clothes for effective wash action
• Helps distribute the load to minimize imbalance and noise
• Guides garment movement for consistent wash action
• Common failure symptoms: loose or missing baffle, rattling/banging sounds, clothes catching or excessive wear

• Disconnect power and shut off water before servicing; wear cut-resistant gloves
• Open the door and rotate the basket to access the baffle fasteners; support the baffle while removing screws
• Align the new baffle with the keyed slots/holes and tighten the screws securely
• Manually rotate the basket to confirm clearance, then run a short test cycle to verify smooth operation

This genuine bracket secures a component inside your appliance cabinet, keeping it aligned and stable so the machine runs smoothly. Replace a bent, cracked, or stripped bracket to restore proper fit and prevent vibration, rubbing, and rattling.

• Provides a rigid mounting point for the specified assembly in your model
• Maintains correct position and spacing between parts
• Helps prevent vibration, rattling, and rubbing noises
• Replace if bent, cracked, or the mounting holes are stripped
• Common symptoms include loose/misaligned parts, unusual noises, or components not staying secured

• Unplug the appliance; shut off gas or water supply if applicable
• Support the attached component while removing fasteners
• Note orientation (take a photo) and transfer any clips/spacers from the original bracket if present
• Tighten fasteners evenly and verify alignment/clearances before use

This door seal creates a tight, protective barrier around the dryer door to help contain heat, airflow and lint for efficient drying and safer operation. It replaces worn or torn seals that let air escape or allow excess lint buildup. What it does:

• Seals gap between the door and cabinet to maintain proper airflow and drying temperature
• Helps prevent lint, dust and small items from escaping the drum area
• Reduces heat loss that can lengthen dry times or lower performance
• Stops drafts and minimizes air leaks that can cause uneven drying

• Disconnect power before beginning any service to avoid shock or injury
• Remove the door and/or access panel per your model's service instructions to reach the seal
• Inspect the door frame and mating surfaces; clean away lint and residue before installing the new seal
• If clips or adhesive are used in your model, replace or resecure them per manufacturer guidance

This replacement rubber foot cushions the machine's contact point with the floor to improve stability, reduce vibration, and protect surfaces. Replace a worn or missing foot to restore steadier, quieter operation and easier leveling.

• Provides a cushioned, non-slip contact point between the appliance and floor
• Helps absorb vibration and reduce rattling or movement during cycles
• Aids in proper leveling and overall stability
• Replace when cracked, flattened, or missing, or if the unit rocks or "walks"

• Disconnect power; for washers, also turn off water. If applicable, shut off gas supply
• Carefully tilt or raise the appliance with assistance and proper lifting support
• Remove the worn foot and install the new foot on the leveling leg or base as designed, ensuring it seats fully
• Re-level the appliance and tighten any locknuts; verify stable operation

A clear silicone adhesive/sealant used to bond and seal appliance trim and components, helping restore watertight and stable assemblies. Supplies a durable, flexible hold for small repairs where factory adhesive is specified. What it does:

• Bonds trim, panels, and small plastic or metal parts to prevent movement and leaks
• Seals gaps to reduce water intrusion around housings and door areas
• Provides a flexible, durable hold that resists vibration and temperature changes
• Useful for reattaching trim, tabs, and molded parts when original adhesive has failed

• One (1) clear 3 oz tube of DOW 737 adhesive

• Use in a well-ventilated area; wear gloves and eye protection to avoid skin/eye contact
• Surface must be clean, dry, and free of oils or old adhesive for best adhesion
• Apply as a thin, even bead; allow recommended cure time before reassembling or using appliance
• Follow any OEM repair instructions and local disposal guidance for adhesive containers