Atw4675yq Parts

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

This electronic control board is the appliance's central controller. It interprets inputs from switches and sensors, then routes power to motors, valves, fans, and heaters so cycles start, run, and complete as intended.

• Coordinates cycle timing and operating modes based on user selections and sensor feedback
• Distributes power to components such as motors, pumps, fans, valves, and heaters
• Monitors safety circuits and stores/triggers diagnostic fault codes
• Common symptoms of a failed board: unresponsive controls, won't start, erratic or stuck cycles, stops mid-cycle, intermittent operation, or no power to components that otherwise test good

• Disconnect power before servicing; also shut off water or gas supply
• Protect from static discharge; handle by the edges and use ESD precautions
• Transfer any wiring, jumpers, or mounting hardware from the original board; match connector orientation
• Some models require configuration/programming after installation—refer to the unit's tech sheet or service instructions

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Used from harness to top.

Right hand side

This outer tub is the main water-holding housing for a top-load washing machine. It supports the inner basket and seals the wash chamber, helping the washer contain water and direct proper wash action. What it does:

• Holds wash water and surrounds the inner basket during fill, wash, and rinse cycles
• Supports the inner tub and transmission/agitator assembly for stable operation
• Prevents leaks by maintaining the sealed wash chamber; a cracked tub can cause visible water under the machine
• Helps reduce noise and vibration by keeping the wash components aligned

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain any remaining water from the tub and remove the washer cabinet or top to access the tub
• Transfer any components (basket, agitator, seals, mounting hardware) only if explicitly listed in your parts list; replace worn seals and gaskets when reinstalling

This pressure switch senses washer water level and signals the control to start or stop filling for correct cycles. It replaces a faulty or intermittent level sensor to restore proper fill and cycle operation. What it does:

• Detects water level via the pressure hose and signals the washer control board
• Can cause overfilling or failure to fill when worn or clogged
• May stop cycles early, prevent agitation or spinning, or cause incorrect water levels
• Fits twist-style pressure hose connections used on many top-load washers

• One pressure switch assembly

• Disconnect power and water supply before starting any repair
• Carefully remove the control panel or access panel per model instructions to access the switch
• Avoid kinking or damaging the pressure hose; ensure a secure twist-style connection
• Verify proper operation after installation; test continuity only with the unit powered off

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Size: .20 Fl. Oz. (6 ml)

Screw: 8-16 x 3/8 inch.

This small tension spring restores the return force in the top lock mechanism so it latches securely and releases smoothly. Replacing a fatigued spring helps the lock operate consistently and keeps the panel/top properly secured.

• Provides the return/tension force for the lock lever or arm
• Helps the lock engage fully and stay secured under vibration
• Restores proper latch feel and consistent lock/unlock action
• Common signs include a loose/floppy lock, poor engagement, or the lock not returning to position

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Note the spring's routing/orientation before removal
• Use needle-nose pliers; mind sharp edges and pinch points
• After installation, manually check lock movement for smooth travel

This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.

• Attaches to the control shaft to select and adjust options/settings
• Replaces knobs that are cracked, broken, or missing
• Fixes a knob that spins freely, slips, or won't turn the control
• Restores proper selection and tactile feedback during use

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the flat/splines on the new knob with the shaft and press on firmly until fully seated
• The pointer aligns with the panel markings before use

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This 1/4 HP motor assembly replaces a worn drive motor to restore proper drive power and rotation. It's a direct-fit mechanical motor intended to bring moving components back to OEM performance and reliable operation. What it does

• Provides drive power for the appliance's rotating components to restore normal operation.
• Replaces a failed or noisy motor that causes little or no rotation, intermittent operation, or a humming/stalling condition.
• Helps eliminate abnormal motor noise, vibration, or overheating when the motor is the root cause.
• Restores consistent mechanical speed and torque for components that rely on the motor to function.

• One 1/4 HP motor assembly

• Disconnect power before servicing; follow all safety precautions.
• Verify mounting orientation, shaft alignment, and proper belt/drive configuration during reassembly.
• Inspect and replace worn belts, pulleys, or mounting hardware as needed to prevent repeat failures.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages