Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Installed a new safety switch and strike. It was a very simple repair and the video described the necessary steps beautifully. Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Used for lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Fix washer leaks during drain cycle with this pump-to-drain hose. If water pools under your machine when draining, this hose replacement stops the leak.
Replaced both inlet and outlet side of pump hoses. Removing the machine cover was the most difficult part of the entire project, and it was not hard at all after watching your "How to" videos. Thanks for excellent service. Read more
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
Fix a washer that won't advance cycles, skips spin, or stops mid-cycle. This timer restores automatic operation. Simple DIY fix with diagrams.
It is a verry simple fix. This website supplied me with a detailed diagram showing exactly where everything goes. Read more
Cushioning pad that installs between the washer lid hinge and cabinet. Replace if cracked, worn, or missing to reduce squeaks and prevent metal wear.
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws. Read more
Inner door panel insert for front-load washer door assembly. Provides structural support and finished interior surface. Replace if cracked or damaged.
With the parts I purchased from you. Read more
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:
The splines inside the bottom agitator that are supposed to fit snug with the agitator shaft were worn down and couldn't catch the shaft anymore. I removed the entire agitator then pulled the top agitator part off of the lower agitator part. I then replaced the lower agitator with the new one I purchased and kept the old top agitator part (the top part was still in good condition and didn't need replacing, although I did replace the "agitator dogs" because they're very cheap and figured it... Read more
Right hand side. For screws use WPW10119828.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Watched several repair videos on YouTube produced by AppliancePartsPros.com for this model Whirlpool washer (videos quite well done). Purchased parts from AppliancePartsPros.com; order correctly filled and parts arrived by FedEx within two working days. Performed repairs as instructed. "Plastic welded" holes in poly outer tub using similar plastic (PP) using a cheap soldering iron - worked perfectly, saved >$150 for new tub. Washer now like brand new. Suggestion - buy the spanner wrench,... Read more
Size: 10-16 x 5/8 inch.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more
Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first. Read more
Used from harness to top.
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.