Ced5832vq1 Parts

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This factory replacement nut is a threaded fastener used to secure appliance components with a mating bolt, stud, or screw. Replacing a worn or missing nut restores a tight, rattle-free fit and helps prevent loosening during operation. What it does

• Works with a bolt, stud, or screw to clamp parts together
• Maintains alignment and resists vibration-induced loosening
• Can help reduce rattling, wobbling, or minor leaks from loose connections
• Typical signs it's needed: missing nut, stripped threads, loose components, unusual vibration/noise

• 1 nut

• Disconnect power (and shut off gas/water if applicable) before servicing
• Start threads by hand to avoid cross-threading; use appropriate nut driver or wrench
• Tighten securely per service information; do not overtighten
• Inspect and replace any damaged mating hardware as needed

This is the 4-position rotary temperature selector switch located behind the control knob. It restores precise temperature selection for the cycle when the original switch becomes worn, intermittent, or stuck on a single setting. What it does:

• Routes power through the correct contacts to deliver the selected temperature
• Provides four distinct temperature options via a rotary control
• Common symptoms include: temperature won't change, only one setting works, dead spots while turning, or a loose/stripped knob shaft
• Helps correct mismatched temperature vs. selection

• 1 rotary temperature selector switch (4-position)

• Disconnect power before servicing
• Remove the console/cover and pull off the temperature knob to access the switch
• Transfer wires one at a time from the old switch to the new to maintain correct positions
• Align the D-shaft/locking tabs, secure the switch in the console, reinstall knob and panels, and test selection

This push-to-turn control knob fits onto the control shaft to operate your appliance's settings. Replace a cracked or stripped knob to restore secure grip, accurate selection, and a clean, factory appearance. What it does:

• Attaches to a push-to-turn control shaft to select temperature, heat level, or settings
• Provides proper alignment and grip for smooth, precise adjustments
• Helps address issues like a cracked hub, loose/wobbly feel, spinning without engaging the stem, or a missing knob

• One push-to-turn control knob

• Allow surfaces to cool; disconnect power and shut off gas if working near live controls
• Pull the old knob straight off the shaft
• Align the new knob with the shaft orientation and press firmly into place—do not force
• Test for smooth operation and proper pointer alignment

This top hinge supports the hinged top or upper panel, allowing it to lift for service and close securely. Replacing a worn hinge restores smooth motion and proper alignment to help eliminate wobble, scraping, or gaps.

• Provides the pivot point for lifting the top/panel
• Maintains alignment and helps the top seat flat when closed
• Restores smooth opening/closing without binding or rubbing
• Common signs of failure: loose or uneven top, squeaks, difficulty lifting/closing, visible bending or cracks at the hinge

• Disconnect power; also shut off gas and allow all surfaces to cool
• Support the top/panel while removing and installing the hinge to prevent strain
• Transfer and tighten existing mounting screws unless new hardware is provided
• After installation, check alignment and clearances; replacing hinges in pairs can improve fit

This replacement seal restores a tight barrier between mating parts inside your appliance to prevent leaks and keep the assembly performing as designed. Swapping a worn or brittle seal helps stop drips and protects nearby components. What it does:

• Creates a reliable seal between components or around a shaft to prevent leakage
• Helps maintain proper pressure/flow within the system
• Typical failure signs: cracks, flattening, swelling, brittleness, or leakage/residue at the joint

• 1 seal

• Disconnect power; shut off water supply if applicable
• Allow hot components to cool before servicing
• Access the sealed joint; capture any residual water if working on a wet system
• Clean mating surfaces; seat the new seal evenly. Use only manufacturer-approved lubricant if specified, then reassemble and test for leaks.

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This is the factory replacement microwave door assembly. It restores a smooth, secure door closure and proper operation so the unit can open and close reliably and look like new. What it does:

• Provides a complete, aligned door to open/close the cavity smoothly
• Ensures latch hooks engage properly so the appliance can operate
• Replaces doors that are cracked, warped, or have broken handle mounts
• Addresses issues like the unit not starting unless the door is pressed, or stopping when the door is moved
• Helps resolve sparking/arcing around the door opening caused by a damaged door choke or screen

• One door assembly

• Disconnect power at the breaker before servicing; microwaves contain high-voltage components
• For over-the-range units, support or remove the microwave from the wall to safely access and handle the door
• Transfer any reusable hardware/hinge pins/trim from the original door as needed
• Align the hinges and verify the door closes, latches, and opens smoothly before remounting

This spring clip secures small panels, brackets, or trim inside your appliance to maintain a snug fit and prevent movement. Replacing a fatigued clip helps restore proper alignment and reduce unwanted vibration or rattling. What it does:

• Provides spring tension to hold a component firmly in place
• Helps prevent vibration, rattling, or shifting during operation
• Replaces a bent, worn, corroded, or missing clip
• Common symptoms: loose or misaligned panel/trim, recurring rattles, or parts that won't stay secured

• 1 spring clip

• Disconnect power (and gas, if applicable) before servicing
• Access the clip location per your model's service/parts diagram
• Note the clip's orientation and attachment points before removal
• Use needle-nose pliers carefully to avoid bending adjacent tabs or brackets

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This gray control knob replaces a worn or broken knob on the console so you can accurately select settings. It fits onto the timer/selector shaft and restores a secure grip with smooth, positive engagement. What it does:

• Attaches to the control/timer shaft on the front panel
• Lets you turn and select cycles or options
• Restores a snug fit when the original knob is cracked or stripped
• Common symptoms: knob spins freely, falls off, won't turn settings, or is missing

• 1 gray control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; retain any insert/clip used by your model
• Align the new knob with the shaft and press firmly until fully seated
• Test all settings for proper engagement

This cycling thermostat regulates dryer drum air temperature by switching the heater on and off at its rated setpoints. It helps maintain consistent drying performance and protects against overheating for safer, more reliable operation. What it does:

• Regulates heater cycling to maintain target drum temperature during a cycle
• Opens on temperature rise and recloses as the air cools to prevent runaway heat
• Failure can present as no heat, weak heat/long dry times, or overly hot operation
• Operates around a 180F open / 140F close rating per catalog specification

• 1 cycling thermostat

• Disconnect power; for gas dryers, also shut off the gas supply
• Access location varies by model; remove the appropriate panel to reach it
• Note wire positions; transfer leads one at a time and secure the thermostat with the original screws
• After installation, clean lint passages and ensure proper vent airflow to prevent overheating and repeat failures

Keep the drive system running smoothly. This idler pulley maintains proper belt tension and tracking so the drum/tub or drive system turns quietly and reliably, helping prevent squeal, slip, and premature belt wear. What it does

• Maintains constant tension on the drive belt to prevent slipping
• Guides the belt for smooth, consistent rotation of the drum/tub or drive system
• Helps reduce belt noise and premature belt wear
• Common symptoms of a worn pulley include squealing/scraping noises, burning rubber smell, the belt coming off or fraying, or no tumble/agitate/spin

• 1 idler pulley

• Disconnect power; turn off gas supply before servicing
• Access the belt path and note routing before removal
• Relieve belt tension, remove the old pulley, and install the new pulley in the same position; ensure the belt is seated on all pulleys
• Manually rotate the system to verify smooth operation before reassembly and testing

WPL VENT KIT, 4-WAY ULT