Cfe3050lsk Parts

This hinge assembly provides the pivot and support for your freezer door or lid, allowing smooth opening and secure closing. Replacing a worn hinge restores alignment and helps the gasket seal to keep cold air contained.

• Supports and pivots the door/lid during opening and closing
• Maintains alignment so the door/lid closes fully and seals properly
• Can help resolve sagging, binding, scraping noises, or doors not closing all the way
• Replaces a bent, cracked, or seized hinge assembly

• Disconnect power before service; wear gloves.
• Support the door or lid and use a second person to prevent drops or damage.
• Transfer any spacers, bushings, or covers from the old hinge if required.
• Align the hinge, tighten fasteners, and verify smooth operation and gasket seal.

The Mullion Striker is an OEM part for GE refrigerators responsible for securing the mullion or flipper door in place when it is closed, ensuring a tight seal and temperature inside the refrigerator.

A bad mullion striker can be caused by normal wear and tear over time, damage due to excessive force or impact, or misalignment of the mullion assembly. If you notice that the mullion door does not stay securely closed, causing a gap or allowing warm air to enter the refrigerator, it may indicate a problem with the mullion striker.

Symptoms of a bad mullion striker include:

• Difficulty in keeping the mullion door closed
• Visible gaps or improper sealing when the door is closed
• Condensation or frost buildup around the mullion area
• Unusual noises from the mullion assembly

Replace your faulty mullion striker with this genuine OEM part to restore your refrigerator. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This triple water inlet valve controls and directs water flow to your refrigerator's dispenser and ice maker. Replacing a sticking or leaking valve restores proper fill and helps stop drips, leaks, and low or no water or ice.

• Opens individual solenoids to route water to the correct circuit (dispenser and ice maker) on demand
• Seals closed to prevent seepage that can cause dripping from the dispenser or ice buildup
• Helps maintain consistent water flow for reliable dispensing and ice production
• Common symptoms include no water at the dispenser, slow flow, ice maker not filling, or leaks from the rear of the refrigerator

• Unplug the refrigerator and shut off the household water supply before service
• Relieve line pressure and place a towel to catch residual water
• Label and transfer each tube and wire connector to the matching port to avoid cross-connection
• Restore water and power, check all connections for leaks, and purge air by dispensing water for several minutes

Almond. Size: 13 oz. can. Acrylic appliance paint.

This cold control kit replaces the mechanical temperature control thermostat that regulates your refrigerator or freezer's cooling. Restore proper temperature regulation and consistent cycling when the original control sticks, drifts out of calibration, or fails intermittently.

• Senses compartment temperature with a capillary bulb and opens/closes contacts to maintain the set temperature
• Cycles the cooling system on and off for steady, reliable performance
• Common symptoms: too warm or over-cooling/freezing items, unit won't start unless the dial is moved, runs constantly, erratic temperature swings, unresponsive temperature dial
• Helps correct intermittent cooling caused by worn or pitted thermostat contacts

• Disconnect power before servicing; work in a dry area
• Access the control housing, note wire locations, and transfer wires to the new control one at a time
• Route and secure the sensing bulb/capillary exactly as original; do not kink or sharply bend it
• Set to a mid-range setting after installation and allow up to 24 hours for temperatures to stabilize

The Heater Harness Fz W/tco is an OEM part for GE refrigerators. This essential component is responsible for preventing ice buildup and ensuring proper defrosting in the freezer compartment. This freezer heater harness with TCO defrost thermostat helps maintain the optimal temperature and humidity levels in your freezer. It is designed to melt away any ice or frost that may accumulate on the freezer coils, preventing them from obstructing airflow and affecting the cooling performance.

A bad freezer heater harness can occur due to wear and tear, electrical faults, or other factors. If you notice symptoms such as excessive ice buildup, inconsistent cooling, or frequent freezer defrosting cycles, it may be time to replace this part.

Symptoms of a bad freezer heater harness with TCO defrost thermostat include:

• Excessive ice buildup
• Inconsistent cooling
• Frequent freezer defrosting cycles

Prevent ice-related issues by replacing the faulty freezer heater harness with TCO defrost thermostat with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Size: 10-32 inch.

The Air Tower is an OEM component for GE side-by-side refrigerator models designed to distribute cold airflow across shelves and crisper bins. Strategically located in the fresh food compartment, it facilitates even temperature regulation within. Efficient airflow relies on an intact tower design.

Symptoms of a defective air tower include:  

• Warm spots or frost buildup noticed on certain shelves and walls   
• Fluctuating temperatures displayed on control panels
• Condensation or moisture issues in unaffected areas

Causes stem from common blockages within vent channels from food debris over time, wear of fan blade bearings reducing distribution power, or cracks in injection-molded tower walls.

Replacing with this genuine GE part restores optimum temperature balance throughout the refrigerator. Compatible for replacement fits Hotpoint, RCA, or Kenmore units seeking uniform chilling without dead zones developing. Regular cleaning helps but replacement maintains long-term efficiency.
 

The Ice Maker Fan Motor is an OEM part for GE refrigerators. It is a critical part of the automatic icemaker located inside the fresh food compartment. The fan motor works to rapidly freeze water into bullet-shaped cubes.

Symptoms of a failing fan motor include:

• Slow or ineffective ice production
• Leaks or water overflow from the icemaker assembly
• Strange noises coming from the icemaking area

Causes can be due to the motor brush wearing out over extended use, damage to the fan blade inhibiting spin, or failure of electronic motor components.

Replacing with this genuine GE fan motor restores timely ice harvests. It's compatible with Hotpoint, RCA, and Kenmore models to keep up with household demand for chilled refreshments.

This clip secures the evaporator thermistor to the evaporator tubing so the control can read coil temperature accurately. Replacing a damaged or missing clip helps restore correct cooling and defrost performance by keeping the sensor firmly in place. What it does:

• Holds the evaporator thermistor tightly against the evaporator coil/tubing for accurate temperature sensing
• Supports proper cooling regulation and defrost cycle timing
• A loose or misplaced sensor may show temperature swings, long run times, or frost buildup on the evaporator
• Restores correct sensor placement after repairs or when the original clip is lost or broken

• 1 evaporator thermistor clip

• Unplug the refrigerator; interior metal edges and fins are sharp—wear cut-resistant gloves
• Remove the evaporator cover to access the sensor; note the original sensor location and orientation
• Transfer the thermistor into the new clip and attach it at the same spot so the sensor makes firm contact; do not pinch wires
• Reinstall panels, keep wiring clear of the fan, and restore power

This cam closure is the small pivot piece that helps the refrigerator fresh-food door close and stay aligned. Replacing a worn or broken cam restores smooth door movement and helps the door seal evenly to maintain cooling. What it does:

• Guides the fresh-food door cam so the door pivots and latches correctly.
• Helps correct sticking doors, doors that hang or bind, and uneven gaps that can let cold air escape.
• Replaces a worn, cracked, or broken closure that can cause misalignment or noisy door operation.

• Disconnect power or unplug the refrigerator before beginning any work.
• Remove the door or access trim per the manufacturer's instructions to reach the cam area; keep track of hinge pins and fasteners.
• Pry or pop out the old cam and press the replacement into the cam slot until it snaps into place; check door alignment and operation after installation.

The Flat Chrome Badge is an OEM part for GE refrigerators. It is responsible for displaying the GE logo and model information on the front of the refrigerator. As an identifiable brand marker, the badge contributes to the overall appearance and style of the appliance.

Causes of a bad badge can include damage from impacts or bending, discoloration or tarnishing over time, or simple wear and tear that renders the badge appearance faded or illegible.

Symptoms of a bad badge include:

• A missing, loose, crooked or illegible badge
• Signs of denting, scratching or corrosion
• An outdated or inconsistent badge that doesn't match the model

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The 2-pack Hinge End Cap Assembly is an OEM replacement part for GE refrigerators. This assembly is responsible for providing support and stability to the refrigerator door hinges, ensuring smooth opening and closing.

A bad hinge end cap assembly can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a loose or sagging door, difficulty in opening or closing the door, or the door not staying securely in place, it may indicate a need to replace this assembly.

Symptoms of a bad hinge end cap assembly include:

• Loose or sagging refrigerator door
• Difficulty in opening or closing the door
• Door not staying securely closed

Restore your refrigerator's door by replacing the faulty hinge end cap assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Quick Space Shelf is an OEM replacement part for GE refrigerators designed to maximize storage space and provide flexibility in organizing your refrigerator. It can be easily adjusted to accommodate taller items, allowing you to customize the storage space according to your needs. It features a mechanism that allows you to quickly and effortlessly create additional vertical space when needed.

A bad Quick Space Shelf can occur due to damage or wear and tear over time. If you notice symptoms such as cracks, broken parts, or difficulty in adjusting the shelf, it may indicate a need to replace the Quick Space Shelf.

Symptoms of a bad Quick Space Shelf include:

• Cracks or broken parts
• Difficulty in adjusting the shelf
• Inability to create additional vertical space

Restore your refrigerator's storage capacity and organization capabilities by replacing the faulty Quick Space Shelf with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Evaporator Cover and Fan Assembly is an OEM part for GE refrigerators. It works to circulate cold air throughout the refrigerator and freezer compartments.

Causes of failure include damage or debris affecting fan rotation. Coil corrosion over time also impacts heat exchange performance.

Symptoms of issues are:

• Abnormally warm refrigerator temperatures
• Frost or ice accumulating inside
• Loud noises from the circulating fan
• Inefficient cooling needing frequent defrosting

This OEM GE  part is also compatible with Hotpoint, RCA, and some Kenmore models.

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.