Cggf3056kf Parts

Uneven baking or convection mode not working? This rear-mounted convection fan heating element circulates hot air for consistent cooking results.

Convection fan won't run or makes noise? This motor powers the fan that circulates hot air for even cooking. Moderate DIY repair restores airflow.

Replacement handle for range oven doors. Installs on the front door panel for gripping and opening. Needed when original handle is cracked or broken.

The gas range drawer front panel is the exterior facing panel on the storage or warming drawer located at the bottom of your gas range. It gives the lower drawer a finished look that matches the rest of the range and provides a handle for opening and closing the drawer. Replace this part if the panel is cracked, dented, discolored, or has come detached from the drawer.

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Routes gas from the inlet regulator to the burner manifold on your gas range. Replace if cracked, leaking, or damaged to restore safe fuel delivery.

This safety valve controls gas flow to the oven burner. When signaled by the igniter, it opens to allow ignition and helps maintain consistent heat, supporting safe, reliable preheating and baking performance.

• Regulates gas flow to the oven burner under control of the igniter and thermostat/electronic control
• Prevents gas from flowing until proper ignition conditions are met
• Common symptoms: oven won't ignite or heat, intermittent heating, extended preheat time, or weak/unstable flame
• Often inspected when the igniter glows but the burner does not light

• Disconnect power and shut off the gas supply before servicing
• Transfer any model-specific fittings or brackets from the original valve
• Use approved thread sealant on threaded connections; support tubing and avoid overtightening
• After installation, leak-check every connection with a soap-and-water or leak-detection solution

Replacement control knob for your range or cooktop. Attaches to the control shaft to adjust heat and function settings. Order when original is cracked, broken, or missing.

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Direct-fit door hinge for gas ranges. Supports and aligns the oven door for smooth opening and secure closing. Replace if worn, cracked, or broken.

This trim is a decorative finish piece for select ranges and wall ovens. It covers gaps and raw edges for a clean look and helps keep adjacent panels properly seated when the original becomes cracked, bent, or missing.

• Provides a finished appearance by covering exposed edges or gaps
• Helps maintain alignment of nearby panels or glass
• Replace if cracked, warped, missing, or no longer seats securely
• Common symptoms include loose/rattling panels and exposed or sharp edges

• Disconnect power; for gas models, also shut off the gas supply
• Wear gloves—edges can be sharp
• Remove old trim and transfer/reuse original screws or clips
• Align the new trim and secure with existing fasteners; confirm proper fit before reassembly

Cast iron cooktop grate provides stable support for pots and pans over gas burners. Replace cracked, warped, or missing grates to restore safe cookware placement.

Burner tube for gas ranges. Connects gas valve to burner assembly. Replace if cracked, corroded, or leaking to restore proper gas flow to cooktop burners.

Replacement water inlet valve that controls water flow to the refrigerator's dispenser and ice maker, restoring proper filling and helping stop leaks. Use this valve to address fill and flow issues caused by a failed inlet valve. What it does:

• Opens and closes the water supply to the dispenser and ice maker so they fill correctly.
• Common symptom: no water dispensed or ice maker not filling.
• Common symptom: continuous water flow, visible leaks, or puddling under the refrigerator.
• Typically located where the household water line connects to the refrigerator; valve failures are a frequent source of water-related dispenser and ice problems.

• Disconnect power and shut off the water supply before starting any repair.
• Tighten fittings to the manufacturer's torque recommendations and check all connections for leaks after installation.