Cgr51p1w Parts

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more

Replace idler, motor mounting clamp and lock Read more

This was more maintenance than a fix. I replaced the door gasket and temp sensor on my dryer. Thought what the heck and it might work more efficiently. I also replaced the shocks on my front loading washer. That was a bit of a chore, but could not have done it without the video that showed how to replace them. The socket was the life saver. All is working just fine. Who knows maybe I'll get another 20 year out of them. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more

Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more

You found the parts we need and we installed them. The sales person was excellent. Read more

Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more

I had to take out the bottom drawer that holds pans. Disconnect the power and pull the oven out. Removed door, rear panel that held the screws for the side panel and lift up and out the side panel. After that it was straight forward as to replacing the hinge. Spent more time cleaning the florr where the oven was than installing the hinge. Read more

Replaced the broken knob with a new one. Read more

Replaced the lines, however the model maytag I was working un is a poor design. When you lift the top up to access the lines, you are putting pressure on the gas lines. If you lift it up, then down several times; then you risk bending the tubing and it will break. My recomendation is for do-it-yourselfers to lift it, install it, and close it in one step so you don't bend or break the lines again. Hope this helps. Brian Read more

Could not level stove. Front leveling legs had pieces broken out where leg contacted floor. Back leveling legs were worn and did not stay at corrected height when stove returned to full weight on floor. Replaced both front and back leveling legs, and stove was able to be leveled. Also bought Touchup Paint for numerous nicks and scratches - color matched perfectly. Read more

• Won't start

This is an easy fix, but Appliance Parts Pros make finding the correct part easy. I looked at many sites to get a new knob, as I was tired of using pliers to start the dryer. The images on the grid are worth their weight in gold! Read more

Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more

Part arrived quickly and was an easy install1 Read more