Dbb1000awe Parts

A replacement strain relief bracket that secures the appliance power cord at the entry point, protecting wiring and the terminal connection from pull and wear. Restores proper cord routing for safer, more reliable electrical connection. What it does:

• Secures the power cord where it enters the appliance to prevent tension on terminals and wiring.
• Helps reduce intermittent power, loose connections, or arcing caused by a tugged or poorly routed cord.
• Maintains correct cord routing and support to match the original mounting location and fit.
• Useful when the original bracket is cracked, broken, or no longer holds the cord firmly in place.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access is typically from the rear; remove the back access panel to reach the cord entry and terminal block.
• Remove mounting screws holding the old bracket, position the cord, and secure the new bracket without over-tightening; reuse original hardware if appropriate.
• Inspect the power cord and terminals for damage—replace damaged wiring.

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

Size: 8-32 t. Includes 12 screws.

Size: 8-18 ab.

This rear level leg bracket replaces the rear mounting bracket that secures a leveling leg to the appliance frame, restoring proper support and helping keep the appliance stable and level for safe, quiet operation. What it does:

• Secures the rear leveling leg to the appliance frame so the cabinet sits evenly
• Restores proper height and prevents the appliance from tilting backward
• Reduces rocking, wobbling, and vibration caused by a damaged or loose bracket
• Helps maintain safe, stable operation under normal load conditions

• Disconnect power (and gas supply if applicable) and move the appliance to a safe, accessible area before starting.
• Support the appliance cabinet so it cannot tip when the rear leg or bracket is removed.
• Use basic hand tools to remove and install the bracket; follow the appliance manufacturer's instructions.
• Inspect the leveling leg and front mounts while servicing; replace any worn or damaged hardware.

This gas valve and pipe assembly controls and routes natural gas from the appliance inlet to the burner manifold, restoring proper fuel flow for ignition and stable burner operation. Designed as a direct-replacement service part. What it does

• Regulates and directs gas flow from the inlet to the oven/range burners.
• Enables proper ignition and stable flame for baking and broiling cycles.
• Works with the appliance's existing manifold and burner orifices to maintain correct gas delivery.

• Turn off gas supply and disconnect power before servicing; follow all safety procedures.
• After installation, check all fittings for leaks with an approved gas leak test (do not use an open flame).
• Replace only with the exact part specified for your appliance; inspect connections and gaskets and tighten to manufacturer torque specs.

This is a single replacement screw used to secure appliance panels and components. It provides a direct one-for-one replacement to restore proper fastening and help eliminate rattles or loose panels. What it does

• Secures trim, access panels, or internal components to prevent movement and vibration.
• Replaces stripped, missing, or corroded screws that cause loose or rattling parts.
• Restores proper alignment so doors, drawers, or panels close and sit correctly.
• Helps maintain safe, stable operation by keeping components fastened.

• Handle with care and use the correct screwdriver to avoid stripping the head.
• Tighten to a snug fit; do not over-torque which can strip threads or crack plastic.
• If the original screw was damaged or the mating thread is stripped, inspect the hole and replace with the correct OEM screw or insert as needed.
• Disconnect power or follow appliance-specific safety steps before accessing internal parts.

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small components to the appliance frame
• Restores proper alignment and helps eliminate rattling or vibration
• Replaces missing or stripped fasteners that prevent parts from staying fixed
• Matches OEM fit for reliable fastening where the original screw was used

• One replacement screw

• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal components
• Tighten snugly but avoid overtightening to prevent thread damage
• Keep removed hardware organized so you can install replacements in the original locations

This gas diffuser directs and evens the burner flame for reliable cooking performance. It helps stabilize heat distribution so burners light and heat more consistently across cookware. What it does:

• Spreads and evens gas flame to reduce hot spots and uneven cooking
• Helps stabilize burner ignition and maintain consistent flame shape
• Prevents direct flame contact with surrounding components
• Addresses symptoms like uneven heating, unstable flame, or partial burner operation

• One gas diffuser

• Turn off the gas supply and unplug the appliance before servicing
• Use basic hand tools; avoid overtightening or distorting the part
• If corrosion or sealed fasteners are present, replace affected hardware and check surrounding components

This motor drive pulley guides the dryer drive belt and helps transfer motor power to the drum for proper rotation. Replacing a worn or damaged pulley restores smooth drum movement and reduces noise. What it does:

• Guides and supports the drive belt so the drum turns evenly
• Maintains belt alignment to prevent slipping or excessive wear
• Reduces squealing or grinding caused by a damaged pulley bearing
• Helps restore normal tumbling when the drum drags or hesitates

• One motor drive pulley

• Disconnect power to the appliance before any service; follow lockout/tagout best practices
• Inspect the drive belt and bearings while replacing the pulley; replace worn belt or bearings as needed
• Typical service requires basic hand tools and access to the dryer cabinet or motor housing

This ceramic terminal insulator protects and supports a range or oven heating-element electrical connection, helping prevent shorts and arcing at high temperatures. It's a simple replacement to restore a secure, insulated terminal connection. What it does

• Insulates and isolates a heating-element or terminal connection from the metal chassis to prevent electrical shorts.
• Helps maintain a stable connection under high-heat conditions so the element can heat properly.
• Common symptom replacement: visible cracking, chipping, burn marks, arcing, or intermittent heating.
• Also used when terminals are loose or the original insulator is missing or degraded.

• One ceramic terminal insulator

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Inspect surrounding terminals and wiring; replace damaged connectors or hardware as needed.
• Handle carefully—ceramic can chip or break if dropped or over-tightened.

Specs: 8-32 ca hxw 1/2

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.