Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces damaged outer and inner door panels to restore appearance and maintain proper door alignment. Replace if panels are cracked, warped, or dented. Verify fit with your model number.
Replaced front panel and inner liner of door (kit), trap duct assembly, both bearing slides (gray and white), and drum front support bearing. Procedure is pretty much what one sees in the video clips. Exceptions in our case included: 1. The fact that our door latch¹ was on the front panel while the door strike² was on the door. The newer (replacement) design has the latch on the door and the strike on the front panel! 2. The new door did NOT have the door latch installed (as shown in the... Read more
Usually ships within 4 - 14 days
Fix buzzing noises or no flame in your gas dryer with a new valve assembly. Solves igniter glow without ignition. Moderate DIY repair with basic tools.
First replaced the gas valve solenoids but that wasn't it. After further research, replaced the gas valve. The lock arm support on the new one didn't line up with the dryer lock base but I just bent the arm back a little to fit. Made sure to use gas tape (thicker) when reconnecting the gas pipe. Verified no leaks. No more high pitched buzzing noise. Read more
Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
Size: 8-32 t. Includes 12 screws.
This assembly includes the gas valve and connecting pipe that control the flow of gas to the dryer's burner. It regulates when gas is delivered to the igniter and burner tube during the heating cycle. Replace this assembly if your gas dryer is not heating, heats intermittently, or if the gas valve fails to open properly during operation.
Replaces the rear mounting bracket that secures a leveling leg to your dryer frame. Needed when the original bracket is cracked, broken, or missing.
Housing cover that protects and encloses the dryer heating element assembly. Replace if cracked, broken, or damaged to restore proper dryer operation.
Replacement rear panel for dryers. Restores the cabinet's back surface when the original is dented, rusted, cracked, or damaged. Secures and protects internal wiring and components.
Secures your dryer motor to the cabinet to reduce vibration and noise. Replace if motor shifts or rattles during operation. Confirm fit with your model.
This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does
Left-hand endcap for dryer drum assembly. Secures and supports the drum end. Replace if cracked, broken, or missing to restore proper drum support.
Secures and stabilizes the adjustable leveling leg on your dryer. Replace if the bracket is cracked, broken, or missing to keep your dryer level on uneven floors.
This is a safety device installed in the gas supply line of a gas dryer that restricts gas flow in the event of a leak or line disconnection. It helps prevent dangerous gas accumulation by limiting the amount of gas that can escape. Replace the leak limiter if your dryer has difficulty igniting, produces a weak flame, or if a gas technician identifies it as faulty during a safety inspection.
Meters gas flow to the dryer burner. Replace if damaged, clogged, or when converting between natural gas and LP. Installs at the burner assembly.
The installation of the correct orifice fixed it. While doing that repair, I installed a new drive belt. My dryer is up and running again. The rapid shipment of the parts was most appreciated.. Thank you. Read more
Ground strap assembly connects drum shaft to dryer frame for electrical safety. Replace if damaged, corroded, or causing startup squealing noise.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
Replacement drum assembly for dryers. Installs as the rotating cylinder that tumbles clothes. Needed when drum is cracked, damaged, or worn out.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.